Source register142 source pages from 20 publishers

Sources Used by Repair Cost Atlas

Every page the guides cite, what it supports and when it was published and read. Angi and HomeAdvisor are one company and count as one publisher; technical and government references explain rules, not installed prices.

Published references

Every source a guide cites

What each page publishes, which guides use it, the date the page shows and the date we read it. Withdrawn or unverifiable sources are not listed.

Showing 142 of 142 sources

SourceWhat it supportsCited inDates
EPA Removes R-410A Installation DeadlineACHR News (The Air Conditioning, Heating & Refrigeration News)Independent Trade Publication

Trade reporting (Joanna R. Turpin, May 21, 2026): EPA finalized changes to the 2023 Technology Transitions rule, removing the January 1, 2026 installation deadline for residential and light commercial AC and heat pump systems manufactured or

Show all figures from EPA Removes R-410A Installation Deadline

imported before January 1, 2025, effective 60 days after Federal Register publication; contractors can keep installing that inventory until supplies are depleted; over 90% of new residential and light commercial equipment already uses next-generation refrigerants; AHRI warns refrigerant prices are likely to rise, raising service costs, as supply continues to fall under the AIM Act.

Page date Read
New Year Ushers in Era of A2L RefrigerantsACHR News (The Air Conditioning, Heating & Refrigeration News)Independent Trade Publication

Trade reporting (Joanna R. Turpin, Feb 20, 2025): the AIM Act mandated the phaseout of R-410A system production after December 31, 2024;

Show all figures from New Year Ushers in Era of A2L Refrigerants

from January 1, 2025 manufacturers can only produce comfort cooling systems with lower-GWP refrigerants such as R-32 or R-454B, both classified by ASHRAE as mildly flammable (A2L); Daikin uses R-32 and Midea, Trane and Johnson Controls use R-454B; Trane states EPA and industry safety standards prohibit flammable refrigerants in equipment originally designed for nonflammable refrigerants; contractors are urged to explain A2L vs R-410A differences to homeowners.

Page date Read
AHRI Standard 210/240: Performance Rating of Unitary Air-Conditioning & Air-Source Heat Pump EquipmentAir Conditioning, Heating, and Refrigeration Institute (AHRI)Industry Trade Association

Technical engineering standards for SEER2 and HSPF2 rating test procedures (AHRI Standard 210/240).

Page date Read
Cost to Replace a Main Water LineAngi / HomeAdvisorIndependent Trade Publication

Main water line LEAK REPAIR as published (updated Jun 2026; the page gives the month only, so the page date is recorded as 2026-06): $354 to $1,696, average $1,025. The page is about repair, not full replacement.

Page date Read
How Much Do Gas Line Installation or Repairs Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Gas line as published: typical $260 to $820; underground installation $15 to $25 per linear foot; pipe material $1 to $9 per foot; trenching $4 to $12 per foot; meter $300 to $600; permits $100 to $300; pressure test $75 to $150; labor $45 to $200 per hour.

Page date Read
How Much Does a Blower Motor Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Blower motor as published: $560 average; by horsepower $100 to $550 (1/4 hp) up to $250 to $2,000 (1 hp); PSC $350 to $800 and ECM $600 to $1,150; labor $150 to $250.

Page date Read
How Much Does a Gas Furnace Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Gas furnace as published: about $7,000 average and $3,800 to $10,000 typical for 1,600 to 2,000 sq ft homes; furnace unit prices by stage, AFUE and BTU (40,000 BTU $2,000 to $3,500; 60,000 BTU $2,500 to $4,200; 80,000 BTU $3,000 to $4,900; single stage $700 to $3,000;

Show all figures from How Much Does a Gas Furnace Cost? [2026 Data]

two stage $1,000 to $3,500; modulating $1,300 to $6,500; 80% to 89% AFUE $500 to $1,500, 90% to 95% $1,000 to $3,000, 96% and above $2,000 to $6,000); labor $500 to $2,000; gas line $250 to $800; permits and inspection $400 to $1,500. The unit price tables are not stated to be installed totals.

Page date Read
How Much Does a New Furnace Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

New furnace as published: $4,814 average; typical $2,823 to $6,897; electric $2,000 to $7,000, natural gas $3,800 to $10,000, oil $6,750 to $10,000, propane $3,700 to $14,200; installed totals by home size from $1,200 to $2,000 (1,000 sq ft) to $6,000 to $10,000 (5,000 sq ft);

Show all figures from How Much Does a New Furnace Cost? [2026 Data]

labor $75 to $100 per hour; permits $400 to $1,500; removal $60 to $330.

Page date Read
How Much Does a Shingle Roof Replacement Cost?Angi / HomeAdvisorAggregated Survey

Shingle roof as published (updated Jun 17, 2026; re-read 2026-11-09): $10,067 average and a typical range of $6,138 to $13,996 (the 2026-10-09 reading showed $10,065 and $6,138 to $13,994); per sq ft 3-tab $1.50, architectural $3.50, luxury synthetic $9.50 ("starting at";

Show all figures from How Much Does a Shingle Roof Replacement Cost?

scope not stated); materials and installation $4 to $12 per sq ft (by roof size 1,000 sq ft $4,000 to $12,000, 2,000 $8,000 to $24,000, 3,000 $12,000 to $36,000); labor about 60% of the cost, or $1.50 to $4 per sq ft; slopes steeper than 6/12 have a higher average labor cost; removing old roofing $1 to $5 per sq ft; peak construction season can raise costs by 15% to 30%, and the page recommends booking in shoulder seasons such as spring or summer.

Page date Read
How Much Does a Standing Seam Metal Roof Cost in 2026?Angi / HomeAdvisorAggregated Survey

Standing seam metal roof as published (updated Jun 19, 2026): $19,000 average ("most homeowners paying around $19,000"; not stated as national) with a typical range of $9,400 to $32,600; $4 to $30 per sq ft installed;

Show all figures from How Much Does a Standing Seam Metal Roof Cost in 2026?

average cost by roof size (all-in) 500 sq ft $3,000 to $13,000, 1,000 $10,000 to $18,000, 1,500 $15,000 to $24,000, 2,000 $18,000 to $32,000, 2,500 $25,000 to $40,000, 3,000 $30,000 to $48,000; installed per sq ft steel $10 to $16, aluminum $11 to $18, zinc and copper $25 to $35; by gauge 22 $10 to $25, 24 $3 to $8, 26 $2.60 to $7 (scope not stated); labor $2 to $6 per sq ft ($3,400 to $10,200 per project); permit $250 to $500; disposal $100 to $800; underlayment $1,100 to $4,200; ice and water shield $125 to $170 per square; metal roof repair $630 to $3,200 on average, most repairs $300 to $1,500; inspections $130 to $360; lifespan 50 to 80 years, and copper or zinc "can approach the 100-year mark"; return on investment 61% to 86%.

Page date Read
How Much Does a Tile Roof Cost?Angi / HomeAdvisorAggregated Survey

Tile roof as published: $17,349 average and a typical range of $8,476 to $26,223 (up to $46,000); $7 to $25 per sq ft overall ($2 to $10 materials, $5 to $18 installation); installed concrete $9 to $18 and clay $8 to $25 per sq ft;

Show all figures from How Much Does a Tile Roof Cost?

material only concrete $2 to $4, clay $3 to $7, terracotta $5 to $10; demolition and disposal of old roofing $1 to $5 per sq ft.

Page date Read
How Much Does AC Evaporator Coil Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Evaporator coil (indoor) replacement as published: $1,350 average (not stated as national) with a typical range of $600 to $2,000 (text $550 to $2,250); unit price by size $550 (2 ton) to $1,100 (5 ton); by style A-coil $1,300, N or Z $1,550, slab $1,200, uncased $800, cased $1,000; labor $400 to $1,000, about $700.

Page date Read
How Much Does AC Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

AC replacement as published: $5,978 average (extremes $1,400 to $12,500); Cost Insights replacement range $3,887 to $8,073; central AC equipment $2,500 to $4,500 and installation $3,500 to $7,000 listed as separate columns.

Page date Read
How Much Does Air Duct Cleaning Cost in Chicago? [2026 Data]Angi / HomeAdvisorAggregated Survey

Air duct cleaning in Chicago as published: $325 average and $260 to $390 typical; metal ducts $130 to $340, flexible $300 to $430; no permit needed for a simple cleaning. A single-city example, not a national figure.

Page date Read
How Much Does Air Duct Cleaning Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Air duct cleaning as published: $390 average; typical $271 to $509; by home size $140 to $250 (1,000 sq ft) to $450 to $900 (3,000 sq ft); by vent count $200 to $400 (8) to $500 to $1,000 (20); labor $90 to $125 per hour for 3 to 8 hours; video inspection $70 to $130; repairs $200 to $800.

Page date Read
How Much Does an AC Compressor Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

AC compressor as published: $1,200 average; $800 to $2,300 range; compressor by size from $700 to $1,300 (1.5 ton) to $1,800 to $2,600 (5 ton); labor $75 to $150 per hour.

Page date Read
How Much Does an AC Evaporator Coil Replacement Cost in 2026?Angi / HomeAdvisorAggregated Survey

Evaporator coil (indoor) replacement as published: $1,350 average with a typical range of $600 to $2,000; all-in price by size $950 to $1,550 (1.5 to 2 ton), $1,100 to $1,700 (2.5), $1,250 to $1,850 (3), $1,350 to $1,950 (3.5), $1,400 to $2,000 (4), $1,500 to $2,100 (5); labor $400 to $1,000.

Page date Read
How Much Does Duct Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Duct replacement as published: $1,250 average and $452 to $2,181 typical across 3,970 projects (includes partial jobs); a 2,000 sq ft home with about 250 linear ft of duct $2,000 to $4,500; $10 to $25 per linear foot.

Page date Read
How Much Does Garbage Disposal Installation Cost in 2026?Angi / HomeAdvisorAggregated Survey

Garbage disposal installation as published: $550 average with a typical range of $200 to $625 (text $150 to $950); aluminum units $70 to $350, stainless steel $400 to $1,200; plumber $45 to $200 per hour and handyman $55 to $75 per hour;

Show all figures from How Much Does Garbage Disposal Installation Cost in 2026?

unit averages $260 (continuous feed) and $310 (batch feed), without confirming that installation is included; accessories such as a dishwasher drain connector $10 to $40, push button $40 to $90, baffle $5 to $45, septic assist cartridge $10 to $50, anti-jam tool $10 to $50.

Page date Read
How Much Does It Cost to Install a Mini-Split? [2026 Data]Angi / HomeAdvisorAggregated Survey

Mini-split as published: $3,000 average; $2,000 to $5,000 range; one zone $500 to $5,000, two zones $1,400 to $7,700, four zones $2,600 to $10,700; permits $250 to $400.

Page date Read
How Much Does It Cost to Pump a Septic Tank? [2026 Data]Angi / HomeAdvisorAggregated Survey

Septic tank pumping as published: $428 average (not stated as national) with a typical range of $292 to $565; by tank size $250 to $550 (750 gal), $325 to $700 (1,000), $375 to $900 (1,250), $450 to $1,100 (1,500), $550 to $1,250 (1,750); inspection $250 to $1,175; tank cleaning $400 to $1,000.

Page date Read
How Much Does It Cost to Replace a Garbage Disposal in 2026?Angi / HomeAdvisorAggregated Survey

Garbage disposal replacement as published: $550 average with a typical range of $200 to $625; unit price by motor size matches Angi ($50 to $225, $120 to $310, $200 to $400); aluminum $75 to $300 and stainless steel $400 to $1,100; labor $50 to $100 per hour.

Page date Read
How Much Does It Cost to Replace a Garbage Disposal? [2026 Data]Angi / HomeAdvisorAggregated Survey

Garbage disposal replacement as published: $550 average (not stated as national) with a typical range of $200 to $625 (text $150 to $950); unit price by motor size $50 to $225 (1/3 to 1/2 HP), $120 to $310 (5/8 to 3/4 HP), $200 to $400 (1 to 1-1/4 HP);

Show all figures from How Much Does It Cost to Replace a Garbage Disposal? [2026 Data]

continuous feed $75 to $1,000, batch feed $75 to $300; labor $50 to $100 per hour, about 1 hour; difficult removal adds $50 to $100.

Page date Read
How Much Does It Cost to Shingle a Roof? [2026 Data]Angi / HomeAdvisorAggregated Survey

Shingle roofs in general (not asphalt only) as published: $10,500 average; typical $7,500 to $24,000; labor $4,500 to $10,800 (average $6,300); permits $250 to $500. Architectural shingles $1 to $3 per sq ft, material only;

Show all figures from How Much Does It Cost to Shingle a Roof? [2026 Data]

shingle removal $1 to $5 per sq ft or $1,000 to $5,000 in total, without confirming a single layer or a dumpster.

Page date Read
How Much Does Main Water Line Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Main water line as published: $1,703 average; typical $647 to $2,834; extremes $200 to $5,000; trench $50 to $250 per linear foot, trenchless $75 to $150; municipal connection $1,500 to $13,000.

Page date Read
How Much Does Roof Repair Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Roof repair as published: $1,174 average; Cost Insights range $395 to $1,967; extremes $150 to $8,000; leak $360 to $1,550, flashing $200 to $500, vents $75 to $250, patch $100 to $1,000.

Page date Read
How Much Does Roof Replacement Cost? (2026)Angi / HomeAdvisorAggregated Survey

Roof replacement as published (updated Jun 17, 2026; re-read 2026-11-09): $9,611 national average and a typical range of $5,903 to $13,380 (the 2026-10-09 reading showed $9,609 and $5,903 to $13,377); $4 to $11 per sq ft, about $7 on average;

Show all figures from How Much Does Roof Replacement Cost? (2026)

by roof size 1,120 sq ft $4,900 to $12,300, 1,790 sq ft $7,800 to $19,700, 2,235 sq ft $9,700 to $24,600, 3,355 sq ft $14,600 to $36,900; per sq ft and total for a 1,500 to 2,000 sq ft roof: asphalt shingles $3 to $7 ($5,800 to $20,000), architectural shingles $4 to $6 ($6,000 to $12,000), metal $7 to $13, composite $4 to $8; steep slopes can add $1,000 to $3,000; contractor labor about $200 to $300 per square, not including materials; removing an old roof $1,000 to $3,000 plus $500 to $1,500 for hauling and disposal ("removal and disposal fees ranging from $1,500 to $4,500"); permits $100 to $1,400; on overlays: "Leaving the existing roof in place makes it hard to detect rotting wood or leaks and adds load to your roof."

Page date Read
How Much Does Roof Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Roof replacement as published: $9,609 average; $4 to $11 per sq ft; for a 1,790 sq ft roof $7,800 to $19,700; by material, asphalt $5,800 to $20,000 and metal $5,700 to $25,000 installed; permits $100 to $1,400. By material, asphalt installed $5,800 to $20,000 per project;

Show all figures from How Much Does Roof Replacement Cost? [2026 Data]

no per-sq-ft figure specific to architectural shingles or standing seam.

Page date Read
How Much Does Septic Tank Pumping Cost? (2026)Angi / HomeAdvisorAggregated Survey

Septic tank pumping as published: $428 average with a typical range of $292 to $565 and extremes of $200 to $1,287; by tank size $250 to $550 up to $700 or more for 2,000 gal; jetting $150 to $450; filter cleaning or replacement $100 to $200; inspection $250 to $1,175;

Show all figures from How Much Does Septic Tank Pumping Cost? (2026)

a maintenance table on the same page lists pumping at $289 to $557, against $292 to $565 in the header.

Page date Read
How Much Does Sewer Line Replacement Cost in 2026?Angi / HomeAdvisorAggregated Survey

Sewer line replacement as published (the page covers replacement, not a spot repair): $3,319 average and $1,388 to $5,323 typical; per linear foot $60 to $250 (full), about $50 (partial), $90 to $250 (CIPP), $60 to $200 (pipe bursting);

Show all figures from How Much Does Sewer Line Replacement Cost in 2026?

excavation $400 to $1,200 per 100 linear feet; extra under a slab $300 to $350 per foot; sewer trap $1,500 to $3,000.

Page date Read
How Much Does Sewer Line Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Sewer line as published: $3,319 average; typical $1,388 to $5,323; extremes $225 to $10,000; $60 to $250 per linear foot for a complete replacement; excavation $50 to $200 per linear foot.

Page date Read
How Much Does Sump Pump Installation Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Sump pump installation as published: $1,100 average; typical $800 to $1,500; submersible $1,200 to $3,000, pedestal $800 to $1,500, crawl space or exterior $1,500 to $4,000; by horsepower $800 to $2,500; battery backup $1,000 to $2,000 additional; labor $50 to $150 per hour; permits $50 to $250.

Page date Read
How Much Does the Average Furnace Repair Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Furnace repair as published: $318 average; typical $133 to $505; Cost Insights $64 to $1,475; labor $50 to $150 per hour. Heat exchanger replacement $500 to $1,500 and repair $100 to $200. The page does not publish an age-times-repair-cost rule or a whole-furnace replacement range.

Page date Read
How Much Does Toilet Installation Cost in 2026?Angi / HomeAdvisorAggregated Survey

Toilet installation as published: $374 average with a typical range of $224 to $533 and extremes of $120 and $826; fixture averages from $375 (two-piece) to $1,000 (upflush); removal $50 to $200; relocating a toilet about $3,000; wax ring replacement $50 to $200; labor about $373.

Page date Read
How Much Does Toilet Installation Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Toilet installation as published: $374 average with a typical range of $224 to $533 and extremes of $120 and $826; fixture price by design (two-piece $375, one-piece $800, elevated tank $700, wall-mounted $700); installation after buying the fixture $373; removal $50 to $200;

Show all figures from How Much Does Toilet Installation Cost? [2026 Data]

flange $145 to $300; flooring $8 to $24 per sq ft.

Page date Read
How Much Does Water Heater Replacement Cost? [2026 Data]Angi / HomeAdvisorAggregated Survey

Water heater replacement as published: $1,348 average; typical $882 to $1,826; tankless $1,400 to $3,900; 50 gallon $800 to $2,500; gas $700 to $2,700; electric $600 to $3,500.

Page date Read
Sewer Line Replacement or Repair CostsAngi / HomeAdvisorAggregated Survey

Sewer line repair as published: about $2,600 average repair (not stated as national) with a typical range of $1,100 to $4,100; per linear foot $50 to $250 (dig and replace), $60 to $250 (trenchless), $80 to $250 (CIPP lining), $60 to $200 (pipe bursting);

Show all figures from Sewer Line Replacement or Repair Costs

camera inspection $300 to $400; damage cleanup $500 to $10,000; landscaping restoration $300 to $10,000.

Page date Read
Standing Seam Metal Roof Installation Cost [2026 Data]Angi / HomeAdvisorAggregated Survey

Standing seam metal roof as published: $19,000 average (not stated as national) with a typical range of $9,400 to $32,600; $4 to $30 per sq ft or $400 to $3,000 per square; installed per sq ft: steel $10 to $16, aluminum $11 to $18, zinc and copper $25 to $35;

Show all figures from Standing Seam Metal Roof Installation Cost [2026 Data]

by gauge 22 $10 to $25, 24 $3 to $8, 26 $2.60 to $7 (scope unclear); labor $2 to $6 per sq ft; underlayment $1,100 to $4,200; disposal $100 to $800.

Page date Read
What Does a Metal Roof Cost to Install? (2026)Angi / HomeAdvisorAggregated Survey

Metal roof as published (updated Jun 19, 2026; re-read 2026-11-09): $11,769 average and a typical range of $6,043 to $18,345, "as low as $1,500 or as high as $34,900" (the 2026-10-09 reading showed $11,764 and $6,043 to $18,340);

Show all figures from What Does a Metal Roof Cost to Install? (2026)

per square foot by style: corrugated $3.50 to $15, metal shingles $7 to $22, sheet metal $4 to $6.50, standing seam $7 to $30; by metal: aluminum $4 to $11, copper $15 to $30, steel $6 to $16, zinc $6 to $12, tin $5 to $12; labor about 60% of the cost on average; a 2,000 sq ft roof at $4 to $30 per sq ft is $12,000 to $90,000 (as printed); repairs about $1,800 on average.

Page date Read
How Much Does a Ductless Mini-Split Cost to Install?Bob VilaIndependent Trade Publication

Mini-split installation as published (page updated Jun 30, 2024): "According to Angi and HomeAdvisor", $2,000 to $14,500 typical range, $3,000 average; single zone $2,000 to $8,800, three zones $3,400 to $13,400, five zones $4,800 to $18,000; 12,000 BTU unit $700 to $3,200;

Show all figures from How Much Does a Ductless Mini-Split Cost to Install?

extra indoor units $450 to $1,600 each; multiroom systems $2,700 to $18,000; HVAC technician labor $300 to $1,500; refrigerant lines about $7 per foot.

Page date Read
How Much Does a Furnace Blower Motor Replacement Cost?Bob VilaIndependent Trade Publication

Blower motor replacement as published (page updated Nov 28, 2022): $250 to $900 typical range, $515 national average; PSC single-speed motor $400 to $500, ECM variable-speed $600 to $800 (its types section says variable-speed $400 to $1,100); labor $150 to $410, $75 to $140 per hour.

Page date Read
How Much Does a Metal Roof Cost? (Standing Seam vs Corrugated)Bob VilaIndependent Trade Publication

Metal roof costs as published: $5,659 to $17,314 typical range, $11,452 national average; prices by metal and style per roofing square (100 sq ft), for example standing seam $200 to $1,000 per square.

Show all figures from How Much Does a Metal Roof Cost? (Standing Seam vs Corrugated)

The page shows a last-updated date of July 19, 2022, and lists its sources as HomeAdvisor, Fixr, HomeGuide and Modernize.

Page date Read
How Much Does a Tankless Water Heater Cost?Bob VilaIndependent Trade Publication

Tankless water heater as published (updated Oct 31, 2023): $1,333 to $3,721 typical range, $2,527 national average, attributed by the page to Angi and HomeAdvisor.

Show all figures from How Much Does a Tankless Water Heater Cost?

Conversion-related extras listed on the page: removing the old water heater $500 or more, a new gas line up to $1,000, piping and insulation about $10 per foot, permits $50 to $100, and an electrician at $50 to $100 per hour when converting from gas to electric. No single tank-to-tankless conversion total is published.

Page date Read
How Much Does Roof Repair Cost? (2026 Price Guide)Bob VilaIndependent Trade Publication

Roof repair as published (page updated June 9, 2023): $379 to $1,758 typical range, $1,060 national average, which the page attributes to Angi and HomeAdvisor ("According to Angi and HomeAdvisor, most roof repairs cost between $379 and $1,758").

Show all figures from How Much Does Roof Repair Cost? (2026 Price Guide)

Signs listed: visible roof damage, leaks, sagging, increased energy bills, frequently clogged gutters.

Page date Read
How Much Does Roof Replacement Cost?Bob VilaIndependent Trade Publication

Roof replacement (page updated April 16, 2024): $5,727 to $12,418, $9,072 national average, which the page attributes to HomeAdvisor and Angi;

Show all figures from How Much Does Roof Replacement Cost?

signs it may be time to replace: a roof over 20 years old, sagging, significant weather damage, visible mold, water stains in the attic, leaks, cracked, torn or buckled shingles, shingle granules in the gutters, moss, and rotting boards; homeowners insurance "may cover roof replacement in some circumstances" but "typically does not include general wear and tear", while damage from severe weather, fire and other covered perils may be covered less the deductible; roofers tend to be busiest in summer and fall, so winter or spring may bring a lower quote.

Page date Read
How Much Does Sewer Line Replacement Cost?Bob VilaIndependent Trade Publication

Sewer line replacement as published (updated Jan 27, 2023): $1,253 to $4,701 typical range, $2,914 national average, attributed by the page to HomeAdvisor.

Page date Read
How Much Does Water Heater Installation Labor Cost? (Hours & Trade Rates)Bob VilaIndependent Trade Publication

Water heater replacement as published (updated Apr 22, 2024): $874 to $1,765 typical range, $1,293 national average. The page attributes these figures to Angi and HomeAdvisor, so they are not an independent check on Angi. The page does not break out installation labor hours.

Page date Read
Air-Source Heat Pumps and Ductless Mini-Splits Energy Efficiency SpecificationsENERGY STAR (EPA and DOE)Government Agency

What ENERGY STAR certification means for air-source heat pumps, cold-climate performance, and where to find certified models and utility rebates. Federal tax credit (Section 25C) details on this page are out of date: the IRS says the credit ended for property placed in service after December 31, 2025.

Page date Read
ENERGY STAR Certified Water Heaters: Residential Sizing & Efficiency SpecificationsENERGY STAR (EPA and DOE)Government Agency

Uniform Energy Factor (UEF) efficiency standards, tank capacity sizing thresholds (40, 50, 75 gal), and heat pump water heater standards. The federal tax credit criteria once listed here no longer apply: the IRS says Section 25C ended for property placed in service after December 31, 2025.

Page date Read
AC Repair Cost: Understanding Common Issues and When to ReplaceFixrIndependent Trade Publication

AC repair and replacement as published (Jul 31, 2026): typical repairs $150 to $650 (about $350); major repairs $2,000 to $3,500; capacitor $100 to $400 (about $175, part $8 to $50); contactor or electrical $150 to $400; refrigerant leak and recharge $200 to $1,600 (about $800);

Show all figures from AC Repair Cost: Understanding Common Issues and When to Replace

R-22 $50 to $150 per lb, R-410A $65 to $120 per lb; condenser fan motor $200 to $700; blower motor $450 to $2,000; compressor replacement $800 to $2,800 with parts and labor, $1,550 average, over $3,000 for larger systems; under warranty $600 to $1,200 for labor and refrigerant, compressor part alone $400 to $1,800; thermostat $100 to $500; evaporator coil replacement $600 to $2,000, cleaning $100 to $400; clogged condensate drain $75 to $250; labor $60 to $150 per hour; after-hours surcharge $50 to $200; diagnostic $75 to $250; new central AC installed $3,000 to $7,500; full AC and furnace replacement $5,000 to $12,500. Rules: 50% rule (30% to 40% after repeated repairs), $5,000 rule, AC units designed to last 10 to 15 years, an R-22 leak points to replacement.

Page date Read
Cost to Clean Sewer LineFixrAggregated Survey

Sewer line cleaning as published: $200 to $600, $250 national average, extremes $150 and $1,000. Rodding $150 to $375; hydro jetting $250 to $1,000; cleaning or repair with a video inspection $300 to $600.

Show all figures from Cost to Clean Sewer Line

After a sewage backup: pipe and sewer line repair or replacement $1,000 to $5,000, damage restoration about $7 per sq ft cleaned. Full sewer line replacement $1,000 to $20,000. Plumbers $75 to $150 per hour. Quoted: "A sewer line replacement costs $1,000 to $20,000, depending on the location of the damaged area, its length, and materials"; after a backup "you may be able to file a homeowners insurance claim to assist with the repairs or cleanup" (not always possible); warning signs include gurgling sinks or drains and water backing up into a tub, shower or sink. A basic main line clog usually takes 1 to 2 hours of plumber time ($75 to $300 of labor).

Page date Read
Cost to Install Central AirFixrAggregated Survey

Central AC as published: $5,800 to $14,400 national average range and $8,750 average (3-ton, 2,000 sq ft); low end $3,750 (3-ton change-out on existing ducts), high end $18,000 (new 3-ton 21 SEER with 300 ft of ducts). Installed by tonnage: 1.5 tons $3,650 to $6,250;

Show all figures from Cost to Install Central Air

2 tons $4,250 to $7,500; 2.5 tons $4,500 to $8,000; 3 tons $5,000 to $9,150; 3.5 tons $5,450 to $9,700; 4 tons $6,950 to $11,600; 5 tons $7,800 to $14,000. Unit only for 3 tons by SEER: 14 SEER $1,725 to $3,600; 16 SEER $2,875 to $6,000; 18 SEER $4,100 to $7,800; 20 SEER $5,750 to $9,600; 21 SEER $6,325 to $10,800. Replacement with existing ducts (3-ton) $5,500 to $10,000; with partial or total duct replacement $7,500 to $16,000; AC and furnace together $7,500 to $21,000 (good ducts) or $9,400 to $27,000 (new ducts); new ductwork $3,600 to $9,500; removal $150 to $250; labor $1,250 to $3,000 with existing ducts, $75 to $250 per hour. Consider replacing an air conditioner more than 15 years old. Also published: materials only for a mid-efficiency 3-ton unit $3,800 to $7,150; SEER tiers are paired with SEER2 (14/13.4 standard in the North, 15/14.3 standard in the South and Southwest, 16/15.3, 17/16.2, 18/17.2, 19/18.1, 20/19.1, 21/20), 15 SEER unit $2,300 to $4,800; installation takes a few hours to a full day, adding ductwork up to two more days; warranties typically 5 to 15 years, 10 on average; you may need a permit or an inspection after installation; the lowest installation prices may come in the winter months when HVAC professionals are less busy; most air conditioners last 10 to 20 years.

Page date Read
Cost to Repair DuctworkFixrAggregated Survey

Ductwork repair as published: $600 national average, $200 to $1,000 average range, $100 low and $6,000 high. By repair type: duct sealing $1,000 to $3,000; leak repair $350 to $650; loose ductwork $100 to $500; insulating ductwork $1,000 to $2,500;

Show all figures from Cost to Repair Ductwork

replacing sections $250 to $3,000; full replacement $3,000 to $6,000. By location (30 linear ft): attic $200 to $850, crawl space $200 to $900, basement $200 to $800. By problem: broken vent $100 to $250, hole $150 to $350, collapsed $500 to $2,500, rodents $450 to $2,000, mold $2,000 to $6,000. Labor $75 to $200 per hour, call-out $75 to $100; inspection $75 to $175; cleaning $350 to $1,000. Ducts typically last 10 to 15 years.

Page date Read
Furnace Repair CostFixrAggregated Survey

Furnace repair as published: $485 national average, $349 to $650 average range, $66 low end and $2,673 high end.

Show all figures from Furnace Repair Cost

Common repairs priced as service call plus part: ignitor $96 to $178, burner $87 to $162, heat exchanger $1,346 to $2,673, control board $390 to $725, limit switch $66 to $122, blower motor $562 to $1,045, flame sensor $68 to $127, thermostat $91 to $169. Technicians $87 to $162 per hour depending on location; cleaning and servicing $192 to $843. Modern high-efficiency systems last 15 to 20 years; units under ten years old may still be under warranty. Also published: signs a furnace needs repair are leaking water, fuel or burning smells, a carbon monoxide alarm, squealing, whistling, groaning or clunking noises, a yellow instead of blue pilot light, and rising utility bills; emergency, weekend, holiday and after-hours calls cost more (no figure); some companies raise service fees in winter.

Page date Read
Furnace Replacement Cost 2026FixrAggregated Survey

Furnace replacement as published: $2,800 to $7,500 national average range, $4,800 average. Installed by fuel: electric $1,800 to $7,300, propane $3,700 to $14,200, natural gas $3,800 to $10,000, oil $6,700 to $10,000. By home size: 1,000 sq ft $1,200 to $2,000;

Show all figures from Furnace Replacement Cost 2026

1,500 sq ft $1,800 to $3,000; 2,000 sq ft $2,400 to $4,000; 2,500 sq ft $3,000 to $5,000; 3,000 sq ft $3,600 to $6,000; 4,000 sq ft $4,800 to $8,000; 5,000 sq ft $6,000 to $10,000. Labor $300 to $1,800 (10% to 40% of the total), $75 to $150 per hour, 4 to 10 hours; removal $50 to $330; permits $50 to $1,500; duct sections $5 to $45 per linear ft, full ductwork installation $1,400 to $6,000, full ductwork replacement $25 to $55 per linear ft; gas or oil lines $9 to $27 per linear ft; 250-gallon tank $600 to $2,500; 240-volt outlet $175 to $500; tune-up $70 to $300. Lifespan 15 to 20 years (oil up to 25, electric 20 to 30); repairs may make sense with 5 or more years of life left. Also published: BTUs by home size 30,000 to 60,000 (1,000 sq ft), 45,000 to 90,000 (1,500), 60,000 to 120,000 (2,000), 75,000 to 150,000 (2,500), 90,000 to 180,000 (3,000), 120,000 to 240,000 (4,000), 150,000 to 300,000 (5,000); most furnace replacements take 4 to 10 hours; most municipalities require a permit to install a new furnace; labor can be lower in spring and fall; signs for replacement are rising energy bills, end of lifespan, frequent repairs, unusual noises or odors, and uneven heating; furnaces of 96% AFUE or higher cost more upfront; DIY installation can void the manufacturer warranty.

Page date Read
Gas Line Installation CostFixrAggregated Survey

Gas line installation as published: national average range $500 to $2,000, $800 average (a typical 25-foot line to a furnace); a 10-foot extension as low as $200; a service line extended several hundred feet plus a new interior line as high as $5,000.

Show all figures from Gas Line Installation Cost

Per linear foot with labor: extension $10 to $20, new installation $15 to $25, relocation $15 to $25, replacement $23 to $35. By appliance per foot: stove $10 to $15, water heater $10 to $15 (text $10 to $18), dryer $10 to $20, fireplace $10 to $20, grill $10 to $20, pool heater $20 to $25, generator $20 to $25. By number of appliances: one appliance and a water heater $1,250 to $1,600, three and a water heater $1,500 to $2,500, five and a water heater $1,650 to $3,500. Installed per foot by pipe: HDPE $10 to $15, CSST $11 to $20, copper $11 to $21, galvanized $11 to $24, black iron $15 to $30. Plumbers $75 to $130 per hour; trenching $4 to $12 per foot; permit $50 to $300; pressure test $75 to $100; inspection $50 to $75; capping a line $75 to $150; sediment trap $100 to $150; earthquake shut-off valve $350 to $1,000. New service: the first 100 feet are free on a new install in most cases; extra 50 feet from the main $850 to $1,100 on average; hook-up to the main $200 to $300; meter $250 to $425 if the utility does not include it. Quoted: "The process can take anywhere from 30 minutes to 2 hours per appliance"; outdoor digging "can take several hours spread over a few days"; "Installing a gas line should not be done DIY"; "Always use a specialized plumber or your utility company"; "You need a permit to install a new gas line"; copper "is illegal to use in many areas".

Page date Read
How Much Does a Heat Pump Cost in 2026?FixrAggregated Survey

Heat pump as published: $8,350 national average, $5,000 to $15,000 average range; by type ductless mini-split $2,000 to $8,000, air-source $5,000 to $15,000, geothermal $15,000 to $35,000;

Show all figures from How Much Does a Heat Pump Cost in 2026?

by home size 1,000 sq ft (2 tons) $5,000 to $8,000, 1,500 sq ft (2.5 to 3 tons) $6,700 to $14,000, 1,800 and 2,000 sq ft (3 to 4 tons) $8,000 to $20,000, 2,500 sq ft (3.5 to 5 tons) $9,500 to $22,000, 3,000 sq ft (4 to 6 tons) $15,000 to $25,000; by efficiency SEER2 14 to 15 $5,000 to $12,000, 16 to 17 $7,000 to $15,000, 18 to 19 $10,000 to $18,000, 20+ $15,000 to $25,000; labor $75 to $125 per hour; permits $50 to $300; removal included in labor. Heat pumps last 10 to 15 years. Also published: most municipalities require permits for any mechanical replacement; schedule installation in fall or spring, which can sometimes lower labor costs; replacement signs are ongoing performance problems, frequent repair calls, unexpected spikes in electric bills, uncomfortable indoor temperatures and older refrigerant; check the warranty, and a longer warranty can save future repair costs; heat pumps may need backup heat in extremely cold climates; older units, especially those made before 2015, may use R-22.

Page date Read
How Much Does a Metal Roof Cost? (Fixr)FixrAggregated Survey

Metal roof as published by Fixr (updated January 23, 2026): a $26,500 national average for a 2,400 sq ft steel roof, a typical range of $14,400 to $38,400, an overall average of about $11 per sq ft within $3 to $30, and per sq ft prices including

Show all figures from How Much Does a Metal Roof Cost? (Fixr)

materials and installation of tin $3 to $15, aluminum $4 to $12, zinc $6 to $12, steel $6 to $16, copper $15 to $30. Also published: by style corrugated $3.50 to $26, metal shingles $6 to $22, standing seam $7 to $30 per sq ft; a 1,000 sq ft home needs about 1,200 sq ft of roofing and a 2,000 sq ft home 2,400 to 2,500 sq ft; by house size 1,000 sq ft $4,800 to $36,000, 2,000 sq ft $9,800 to $73,500; labor $3 to $12 per sq ft ($300 to $1,200 per square), 50% to 80% of the total (the DIY section says 50% to 60%); removing an old roof $1,000 to $7,400; underlayment $0.05 to $0.50 per sq ft; metal costs two to three times as much as asphalt shingles and lasts at least twice as long; metal averages $11 per sq ft against $4 for asphalt shingles; lifespan 50 to 70 years (steel up to 60); "While it's possible to install a metal roof over existing shingles, it's usually best to rip the old roof off and start fresh"; roofers are busiest in late spring and early summer; insurance may cover part of a replacement after extreme weather damage, less the deductible.

Page date Read
How Much Does a Roof Replacement Cost in 2026?FixrAggregated Survey

Roof replacement as published by Fixr: $10,000 national average, typical range $7,500 to $14,000, $4.75 per sq ft on average within $3.75 to $11;

Show all figures from How Much Does a Roof Replacement Cost in 2026?

tear-off, removal and disposal $50 per square on average including dumping fees, up to $150 per square for heavier materials such as concrete tile or multiple layers of asphalt; totals for about 2,000 sq ft of roofing: asphalt $6,000 to $10,000, metal $14,000 to $38,000, clay tile $14,000 to $28,000, concrete tile $14,000 to $24,000, slate $20,000 to $60,000. Also published: architectural shingles $8,000 to $32,000, cedar shake $10,000 to $30,000 for the same roof; by roof size 1,000 sq ft $3,750 to $11,000, 1,500 sq ft $5,625 to $16,500, 2,000 sq ft $7,500 to $22,000, 2,500 sq ft $9,375 to $27,500, 3,000 sq ft $11,250 to $33,000; replacing roof decking $2 to $8 per sq ft; fascia and soffit repairs $500 to $2,500; significant rafter damage can add up to $5,000; labor 40% to 60% of the total, or $4,000 to $6,000 on average; permits $100 to $500; ice and water shield about $0.50 per sq ft (about $50 per square); repairs average $1,150. Estimates usually include a manufacturer's warranty and a workmanship warranty, and contractors offering longer or more comprehensive coverage often charge higher labor rates; coastal and urban areas typically pay more than rural regions. Also on the page: more size rows, 1,200 sq ft $4,500 to $13,200, 1,600 $6,000 to $17,600, 1,700 $6,375 to $18,700; "A new asphalt roof averages $10,000"; replacement "will disrupt you and your family for between one and seven days"; "Most cities require permits for roof replacement, typically costing $100 to $500", and some areas require fire-, impact- or wind-resistant materials; repair can suit localized damage on a roof with "10+ years of useful life left", while "Replacement is better for widespread wear, moss, or missing shingles"; "If the roof was damaged by storm, hail, or wind, homeowner's insurance may cover part or all of the replacement"; "Roofing demand drops in fall and winter, which can lead to lower labor costs and faster scheduling"; an overlay can save labor and disposal "If local codes allow".

Page date Read
How Much Does AC Installation Cost in 2026?FixrAggregated Survey

AC installation as published: $5,000 to $12,000 national average range, $6,000 average; by type portable $100 to $500, window $150 to $800, ductless mini-split $1,000 to $14,500, air-source heat pump $4,000 to $11,000, central AC $5,000 to $12,000, geothermal $11,000 to $38,000;

Show all figures from How Much Does AC Installation Cost in 2026?

by tonnage (materials and labor) 1.5 ton $1,800 to $7,000, 2 ton $2,000 to $7,600, 3 ton $2,500 to $8,000, 4 ton $3,100 to $8,700, 5 ton $3,300 to $9,300; labor $500 to $2,500 for a standard central system, $75 to $250 per hour; ductwork $1,400 to $6,000; permits $50 to $1,500; central air replacement average $6,000.

Page date Read
How Much Does AC Repair Cost? [2026 Data]FixrAggregated Survey

AC component replacement as published by Fixr: indoor evaporator coil $400 to $2,700 and outdoor condenser coil $600 to $2,400; HVAC labor $75 to $175 per hour; refrigerant recharge $100 to $600 as a separate service.

Show all figures from How Much Does AC Repair Cost? [2026 Data]

Also published: AC repair $375 on average ($250 to $700 typical, up to $3,000); service call from $75; emergency $150 to $300 per hour; compressor $600 to $3,000; capacitor $100 to $400; condensate pump $100 to $500; drain pan $200 to $600; clogged condensate line $75 to $250; circuit board $100 to $700; thermostat $150 to $500; expansion valve $300 to $500; blower motor $300 to $2,000; refrigerant leak repair $200 to $1,500; ductless mini-split repair $300 to $1,000; central AC repair $150 to $2,000. Replace when a repair costs more than 50% of a replacement; its FAQ also describes the $5,000 rule (repair cost times age in years).

Page date Read
How Much Does Air Duct Cleaning Cost in 2026?FixrAggregated Survey

Air duct cleaning as published: most homeowners $300 to $700, $500 national average for a 2,000 sq ft home, $150 low and $1,050 high; by home size 1,000 sq ft $150 to $350, 1,500 sq ft $225 to $525, 2,000 sq ft $300 to $700, 2,500 sq ft $375 to $875, 3,000 sq ft $450 to $1,050;

Show all figures from How Much Does Air Duct Cleaning Cost in 2026?

$0.15 to $0.35 per sq ft; $25 to $50 per vent and up to $75 per return; 8 vents $200 to $400 up to 20 vents $500 to $1,000; labor $90 to $130 per hour for 3 to 6 hours; dryer vent about $140 extra; video inspection $70 to $150; mold remediation $1,000 to $5,000; pest removal $200 to $1,200; HVAC tune-up $60 to $250. Cleaning every three to five years; avoid unusually low flat-rate offers that lead to upcharges. Also published: 1,200 sq ft $180 to $420; 12 vents $300 to $600, 16 vents $400 to $800; most cleanings take around five hours; ductwork services (sealing, repairs) $500 to $4,000; individual duct repairs $175 to $2,100; asbestos or lead testing $250 to $800; in-duct air purifier about $2,500; get at least three estimates and check NADCA certification.

Page date Read
How Much Does an Asphalt Shingle Roof Cost in 2026?FixrAggregated Survey

Asphalt shingle roof as published by Fixr: $12,000 national average and a typical range of $8,000 to $16,000; per sq ft including materials and labor: 3-tab $3 to $5, architectural $4 to $8, luxury or designer $6.50 to $16;

Show all figures from How Much Does an Asphalt Shingle Roof Cost in 2026?

tear-off and disposal, if billed separately, $50 to $150 per square. Also published: "Labor accounts for around 50% to 60% of your total" and "you'll be paying between $1.50 and $9.60 per square foot for labor alone"; labor usually includes removing the old roof, laying underlayment and flashing, and installing the new roof; roof decking repair adds $150 to $1,000; ice and water shield costs about $1,000 on average as an upgrade; rigid foam insulation in hot climates $1,000 to $2,000; permits $100 to $500; lifespan 3-tab 15 to 20 years, architectural 25 to 30 years, luxury 30+ years; average repair $1,150; Owens Corning, CertainTeed and GAF are described as budget-friendly brands and Tamko and IKO as higher-end brands that may include better warranty coverage; manufacturers and installers that offer longer and more robust warranties usually cost more; by house and roof size: 1,000/1,200 sq ft $3,600 to $19,200, 1,500/1,800 $5,400 to $28,800, 1,700/2,000 $6,000 to $32,000, 2,000/2,400 $7,200 to $38,400, 2,500/3,000 $9,000 to $48,000, 3,000/3,600 $10,800 to $57,600. Also on the page: asphalt shingles are on more than 80% of U.S. homes (citing the Asphalt Roofing Manufacturers Association); "Most homeowners go with architectural shingles"; replacement is worth considering when the roof is within 5 to 10 years of its 25 to 30 year life, when leaks keep recurring, or when energy efficiency is poor; "Roofers are usually busiest in the spring, so you may enjoy lower labor costs in the fall"; homeowner's insurance may cover part or all of a replacement if a tree or natural disaster damaged the roof; an overlay is possible "If it's legal in your municipality and your existing roof is in good condition"; the replacement averages $12,000 against $1,150 for a repair.

Page date Read
How Much Does Heat Pump Repair Cost in 2026?FixrAggregated Survey

Heat pump repair as published: $400 average, $150 to $650 typical. Service call $75 to $250; drain line cleaning $75 to $300; thermostat replacement $85 to $300; capacitor $100 to $400; condensate pump replacement $100 to $450; refrigerant recharge $100 to $600;

Show all figures from How Much Does Heat Pump Repair Cost in 2026?

evaporator coil cleaning $100 to $700; circuit board $150 to $700; drain pan $200 to $800; refrigerant leak repair $200 to $1,500; expansion valve $250 to $800; blower motor $300 to $1,000; reversing valve $350 to $700; evaporator coil replacement $550 to $2,500; compressor replacement $800 to $2,500; condenser coil replacement $900 to $2,300; condenser replacement $1,000 to $4,000; air handler replacement $1,500 to $3,500. Hourly $75 to $150 after the first hour. Replacement averages $8,350. Repair when the system is under 10 years old and the problem is minor; the $5,000 rule and 50% rule are described in the FAQ.

Page date Read
How much does it cost to clean a septic tank?FixrAggregated Survey

Septic tank cleaning as published by Fixr: $400 average with a typical range of $300 to $600 for pumping a 1,250 gallon tank in good condition;

Show all figures from How much does it cost to clean a septic tank?

scenarios from $200 (750 gallons in good condition) to $1,100 (cleaning the walls of a 1,500 gallon tank in poor condition, pumping and cleaning the filter); hydro jetting of tank walls $250 to $300; riser $100 to $200; separate one-time inspection $100 to $300. By tank size: 750 gal $175 to $300, 1,000 gal $225 to $400, 1,250 gal $300 to $600, 1,500 gal $345 to $600, 1,750 gal $400 to $700. Clogged household lines leading to the tank $350 to $650. Pump every 3 to 5 years (a 750-gallon tank with 3 to 5 occupants about every 2 years). Signs the tank is full: a foul odor near the tank or in the drains, soggy areas or poor drainage around the tank and drain field, and slow drains in every sink and tub at once.

Page date Read
How Much Does It Cost to Install a Ductless Air Conditioner?FixrAggregated Survey

Ductless AC as published: $6,357 national average, $4,577 to $8,328 average range, $1,916 low and $21,827 high; HVAC installers $86 to $157 per hour; an electrician adds $101 to $183 per hour.

Show all figures from How Much Does It Cost to Install a Ductless Air Conditioner?

Wall-mounted units are the least expensive and ceiling-mounted units cost the most (no prices given). Also published: the HVAC contractor typically secures any necessary permits and absorbs the cost in the price; compare equipment warranties and ask whether the installer warrants the installation.

Page date Read
How much does it cost to install a garbage disposal unit?FixrAggregated Survey

Garbage disposal installation as published by Fixr: $500 average with a typical range of $300 to $600 for a 1/2 HP batch-feed stainless steel unit, equipment and labor; scenarios from $200 to $750; removal and reinstallation $350 to $700; plumber $75 to $200 per hour;

Show all figures from How much does it cost to install a garbage disposal unit?

removal $50 to $100. Unit prices (unit only): continuous feed $50 to $300, batch feed $100 to $400; aluminum $50 to $200, stainless steel $100 to $400; 1/3 HP $50 to $150, 1/2 HP $100 to $225, 3/4 HP $175 to $300, 1 HP $200 to $400. Electrician $40 to $120 per hour for replacement work, installation labor $120 to $360; a new outlet (typically GFCI) $120 to $200; handyman $50 to $125 per hour. Quoted: "Installing a unit usually takes about 3 hours" (2 to 4 hours to remove an old unit and install a new one); "Most units last between 10 and 12 years before replacement"; replace when you need to press the reset button often or the unit clogs often.

Page date Read
How Much Does It Cost to Install a Gas Water Heater? [2026 Data]FixrAggregated Survey

Gas water heater replacement as published: $1,000 to $2,700 for a standard tank in an existing gas setup, $1,900 average; tankless $1,600 to $4,000.

Show all figures from How Much Does It Cost to Install a Gas Water Heater? [2026 Data]

By tank size: 30 gal $700 to $2,100, 40 gal $700 to $2,300, 50 gal $900 to $2,500, 75 gal $1,100 to $3,500, 80 gal $1,300 to $4,000. Labor for a tank replacement $200 to $650 (about 20% to 25% of the total); tankless labor $800 to $2,000 (about 50%); plumbers $45 to $200 per hour. Disposal $100 to $500. Venting replacement $500 to $1,100 (about $500 for direct vent, about $1,100 for power vent). Simple permit $25 to $300; $1,500 or more with a new gas line or major changes. Switching from electric or oil to gas $3,500 or more. Household size by tank: 30 gal 1 to 2 people, 40 gal 1 to 4, 50 gal 3 to 5, 75 gal 4 to 6, 80 gal 6 or more. Quoted: "Propane water heaters cost about the same as natural gas water heaters, but they generally cost more to run"; "It takes two to three hours, on average, for a professional to install a gas tank-style water heater" (tankless four to six hours); "Tank-style water heaters last for 8 to 12 years, and tankless water heaters can last for 10 to 20 years"; "Repairs are usually worthwhile if the unit has at least half its lifespan remaining"; "Most municipalities require permits for plumbing and gas line work". Warning signs listed: not enough hot water, end of expected life, discolored water, unusual noises, leaks, unusually high energy bills. Anode rods: inspect and replace every 2 to 3 years (no price on this page).

Page date Read
How Much Does It Cost to Install a Thermostat in 2026?FixrAggregated Survey

Thermostat replacement as published: about $200 on average, $85 to $300 national range; manual $50 to $150; non-programmable electronic $85 to $200; programmable $100 to $300 (text also says $100 to $400); smart or Wi-Fi $185 to $600; labor $65 to $200 ($65 to $100 per hour);

Show all figures from How Much Does It Cost to Install a Thermostat in 2026?

new wiring $90 to $400; moving a thermostat $200 to $560; permits $50 or more; repairs usually at least $150.

Page date Read
How Much Does It Cost to Install a Toilet? [2026 Data]FixrAggregated Survey

Toilet installation as published by Fixr: "The average cost to install a toilet is $450, including materials and labor", with a typical range of $250 to $800; low-end $200 and high-end $4,000 in the summary box; a first installation in a new location $1,000 to $3,500;

Show all figures from How Much Does It Cost to Install a Toilet? [2026 Data]

labor alone $150 to $440; plumbers $75 to $150 per hour; permit $50 to $300; removal $50 to $200 if billed separately; drywall patch $75 to $100. "Installation Cost Range" by type: two-piece $200 to $950, one-piece $250 to $1,100, composting $250 to $1,500, corner $325 to $1,300, bidet $350 to $3,000+, wall-mounted $500 to $2,000, macerating $600 to $1,300, smart $750 to $4,000+; by flush type: gravity $200 to $950, dual-flush $250 to $1,200, pressure-assisted $500 to $2,000, upflush $600 to $1,300. Quoted: "Most professionals can replace a toilet in just an hour or two, but the installation could take up to 4 hours or longer if it's a more complex job". Signs listed: cracks, water around the base, frequent clogs, constant repairs, a constantly running toilet, rocking, a soft or creaking floor.

Page date Read
How Much Does It Cost to Install a Water Heater? [2026 Data]FixrAggregated Survey

Water heater installation as published: national average range $900 to $3,000, average about $1,400 for a replacement; overall range $500 to $4,600.

Show all figures from How Much Does It Cost to Install a Water Heater? [2026 Data]

By type, installed: tank $600 to $2,500, tankless $1,000 to $4,000, indirect $1,200 to $4,500, heat pump or hybrid $1,200 to $4,600. By fuel: electric $500 to $3,500, propane $700 to $2,500, natural gas $700 to $2,700, oil $1,200 to $4,500, solar $1,700 to $5,500. By tank size: 30 gal $550 to $2,100, 40 gal $550 to $2,300, 50 gal $700 to $2,500, 75 gal $1,100 to $3,400, 80 gal $1,200 to $3,600. Labor $300 to $1,500 on average, plumbers $45 to $200 per hour. New installation instead of a replacement adds $400 to $1,800 to rough in utilities. Removal and disposal $75 to $500 if charged separately; permits $25 to $1,500; power venting $300 to $1,000. Household size by tank: 30 gal 1 to 2 people, 40 gal 1 to 4, 50 gal 3 to 5, 75 gal 4 to 6, 80 gal 6 or more. Signs it is time to replace: old age (tank units last 8 to 12 years, tankless 15 to 20), leaks, insufficient hot water, unusual noises, high utility bills, strange odors or discolored water. Quoted on the page: "In most cases, homeowner's insurance will not cover water heater replacement"; "Late spring or early summer is typically slower for plumbers, which may result in lower labor costs"; "Most local building departments will require permits to replace a water heater".

Page date Read
How Much Does It Cost to Replace a Roof in Florida?FixrAggregated Survey

Florida roof replacement as published (January 31, 2025): $11,000 to $30,000, $15,729 average, about $15,000 for a 1,700 sq ft roof; asphalt shingles $4.50 to $10 per sq ft in Florida;

Show all figures from How Much Does It Cost to Replace a Roof in Florida?

removal of the old roof about $1 per sq ft on average, up to $4 per sq ft for heavier materials such as slate or metal; permits $400 to $1,000.

Page date Read
How Much Does It Cost to Shingle a Roof?FixrAggregated Survey

Shingle roof as published by Fixr (updated January 30, 2026): $14,500 average, $8,000 to $36,000 for most projects, $4 to $18 per sq ft across shingle materials (asphalt $3 to $16);

Show all figures from How Much Does It Cost to Shingle a Roof?

under its "Labor Cost to Install Roof Shingles" heading, labor averages 60% of the total and usually covers tear-off and haul-away, underlayment and installation; labor "averaging just under $9,000"; permits $150 to $600; "Local building codes determine how many shingle layers are allowed. Some municipalities permit only one layer, while others allow two or even three layers before a full tear-off is required"; roofers are busiest in summer and fall, so late winter or early spring may bring lower labor costs.

Page date Read
How much does it cost to unclog main sewer line?FixrAggregated Survey

Sewer line pricing from a page about clearing clogs: repairing a pipe $50 to $250 per linear foot; replacing a broken or sagging section $1,500 to $3,000; camera inspection $100 to $800; root removal $100 to $800 (text $100 to $600).

Show all figures from How much does it cost to unclog main sewer line?

Clearing a main sewer line clog as published: $475 national average, $350 to $650 range. Snaking $100 to $500; hydro jetting $350 to $600; video inspection $100 to $800 (up to $1,500 for the whole system); cleanout installation $600 to $2,000; cleanup after a sewage backup $2,000 to $10,000; sewer pipe repair or section replacement $50 to $250 per linear foot.

Page date Read
How Much Does Roof Repair Cost in 2026?FixrAggregated Survey

Roof repair as published by Fixr (updated January 21, 2026): $1,150 average, most projects $400 to $1,900; $3.50 to $11 per sq ft on average (slate up to $25), or $350 to $1,100 per roofing square;

Show all figures from How Much Does Roof Repair Cost in 2026?

by scope minor $150 to $1,000, moderate $1,000 to $3,000, major $2,000 to $6,000+; by damage: vent repair $75 to $250, damaged or missing shingles $150 to $700, roof hole $150 to $1,200, water damage $150 to $6,000, flashing repair $200 to $600, wind or hurricane damage $250 to $6,500, skylight leak $300 to $800, roof leak $350 to $1,500, ice dam removal $400 to $1,500, soffit and fascia repair $500 to $6,000, hail damage $700 to $4,000, sagging roof $800 to $5,000, tree impact damage $900 to $6,000; by part: roof decking $150 to $1,000, gutters $200 to $600, ridge capping $200 to $750; by material: asphalt shingles $150 to $1,500, flat roof $300 to $1,100, wood shakes $350 to $1,500, metal $500 to $2,000, clay or concrete tile $500 to $2,500, slate $700 to $3,000; labor at least 60% of the total (up to about 90% for jobs with few materials), roofers $50 to $120 per hour; same-day or next-day emergency work adds $100 to $300; permits $70 to $250; roof inspection about $250. Repair-or-replace guidance: repair if the repair costs less than half of a replacement and the roof has more than half of its life left; a roof over 15 years old with frequent problems may be better replaced. Homeowner insurance may pay when damage results from an unavoidable natural disaster ("like a hurricane, a hail storm, a tornado, or a fallen tree or tree limb"), and "Insurance usually won't cover damage related to old age, poor maintenance, or neglect." Signs of needed repair include water damage on upper-floor ceilings and heavy moss growth.

Page date Read
HVAC Service: How Much Does HVAC Repair Cost? (2026 Guide)FixrIndependent Trade Publication

HVAC repair as published (Oct 22, 2026): $150 to $650 generally, $350 national average; $100 to $3,000 full residential range and up to $5,000+ for severe issues; diagnostic fee $75 to $200; labor $75 to $150 per hour; after-hours 50% to 100% higher or an added $100 to $300.

Show all figures from HVAC Service: How Much Does HVAC Repair Cost? (2026 Guide)

Line items: refrigerant leak repair and recharge $200 to $1,500; R-410A $50 to $80 per lb (recharge $150 to $600); R-454B $60 to $100 per lb (recharge $250 to $700); R-22 can exceed $150 per lb; capacitor $100 to $400; compressor $1,000 to $3,000 or more, $600 to $2,650 under warranty; heat exchanger $1,000 to $3,500+; thermostat $100 to $500; ductwork $200 to $2,100 (about $660 average); furnace repair $150 to $600 with a $350 to $400 average; igniters $150 to $400; flame sensors $100 to $300; pressure switches $200 to $400; AC repair about $750 ($350 to $1,800); heat pump repair $410 average ($161 to $661). Describes the $5,000 rule (repair cost times age) and the 50% rule. Also published: routine furnace repairs $130 to $500 (about $300); the diagnostic fee is often applied to the repair if you hire the same company, and diagnosis usually takes 30 to 60 minutes; a faulty capacitor can make a blower motor hum without spinning and is often misdiagnosed as a motor failure; low refrigerant means a leak to fix; under a compressor warranty homeowners typically pay only labor, refrigerant and small parts; calls R-454B the new 2026 standard and R-22 phased out.

Page date Read
Main Water Line Installation CostFixrAggregated Survey

Main water line replacement as published: $1,500 to $12,000, $3,750 average (a typical 25-foot line installed trenchless); low end $1,125 (10 feet of PVC, trenchless), high end $22,500 (100 feet of copper in a dug trench). $75 to $225 per linear foot, most pay $100 to $200.

Show all figures from Main Water Line Installation Cost

By length: 10 ft $750 to $2,250, 25 ft $1,875 to $5,625, 50 ft $3,750 to $11,250, 75 ft $5,625 to $16,875, 100 ft $7,500 to $22,500. Trenchless $75 to $150 per foot; digging and backfilling $175 to $225 per foot. Materials per foot: PVC $0.50 to $5, polyethylene $2 to $5, copper $20 to $30. Plumbers $75 to $150 per hour. Moving a main water pipe $100 to $250 per foot; main shut-off valve $200 to $1,000; municipal tap replacement $300 to $500; permit $50 to $400; flushing $50 to $100; pressure regulator $250 to $400; repair instead of replacement $500 to $2,000. The page describes the main line as extending "from the edge of your property to the water meter at your house". Quoted: "Your regular home insurance does not usually cover the main water line" (it suggests asking about service line coverage). Signs listed: a water bill that rises without more use, unusually green grass over the line, low pressure and soggy ground.

Page date Read
Roof Underlayment Replacement CostFixrAggregated Survey

Roof underlayment as published (January 31, 2025): $800 to $1,200, $900 national average; material per sq ft: asphalt felt $0.05 to $0.50, synthetic $0.17 to $0.55, rubberized asphalt $0.55 to $0.65, ice and water shield $0.75 to $0.90; installation labor $0.15 to $0.50 per sq ft.

Page date Read
Septic Tank Repair CostFixrAggregated Survey

Septic repair as published: $750 to $3,000, $2,000 national average, extremes $150 and $20,000; full tank replacement $9,500 to $15,000. Pump repair $250 to $1,500; pump replacement $250 to $500; float replacement $150 to $500; effluent filter replacement $200 to $300;

Show all figures from Septic Tank Repair Cost

baffle repair or replacement $300 to $900; lid repair or replacement $150 to $500; pipe repair $200 to $800; distribution box $500 to $1,500; drain field repair $1,000 to $5,000; drain field replacement $2,000 to $20,000. Backing up $250 to $1,000. Inspection $100 to $900; hourly rate $125 to $250; emergency premium 25% to 50%.

Page date Read
Standing Seam Metal Roof: Pros, Cons, and CostFixrAggregated Survey

Standing seam metal roof as published by Fixr: $8.50 to $34 per sq ft by material. The page does not say whether the range includes labor, removal or permits.

Page date Read
Tankless Water Heater Installation CostFixrAggregated Survey

Tankless water heater installation as published: $2,500 to $4,500, $2,811 average; low end $1,058 (single-point 240V electric), high end $6,698 (whole-house solar). Labor and total by fuel: electric labor $500 to $1,000, total $1,000 to $3,000;

Show all figures from Tankless Water Heater Installation Cost

gas or propane labor $900 to $1,500, total $1,400 to $3,500. Plumber $75 to $130 per hour; installation 6 to 10 hours. New gas line adds up to $800. Converting from a tank: gas line about $500, electric installation $90 to $450, gas installation including the gas line about $1,700. Replacing a tankless unit: labor $135 to $1,200, total $600 to $6,000. Unit cost by GPM (gas): 2 to 3 GPM $250 to $600, 5 to 6 GPM $500 to $800, 8+ GPM $900 to $2,000. Removal and disposal of the current system upwards of $500. Annual operating cost: gas tankless $250, gas tank $275, propane tankless $350, electric tank $450, electric tankless $600. The page also cites an average saving of "roughly $116 a year" for tankless versus a storage tank (credited to the Chicago Tribune), without reconciling it with its own table. Electrician $65 to $85 per hour. Unit cost: single-point $150 to $300, whole-house $450 to $1,500; cold-climate venting and insulation "can add up to $400"; a new gas line can add "as much as $800" (the conversion section says about $500). Tankless units last "over twenty years"; tank units 10 to 15 years. Quoted on flow limits: "It is difficult to find this heater type in outputs of more than 7 to 8 GPM", and a home with several people bathing while appliances run "cannot be supported from one unit".

Page date Read
Water Heater Repair CostFixrAggregated Survey

Water heater repair as published: national average range $150 to $750, average $450, extremes $75 and $2,000. By power source: electric $100 to $650, gas or propane $150 to $750.

Show all figures from Water Heater Repair Cost

Part replacement with labor: fuse $50 to $75, pilot light $75 to $150, thermostat $100 to $250, dip tube $100 to $250, valve $100 to $300 (shut-off or drain $100 to $200, pressure relief $100 to $250, gas control $150 to $300), anode rod $125 to $300, thermocouple $150 to $325, heating element $200 to $750, tank $600 to $2,000. By problem: leak $50 to $600, backdraft $100 to $500 (may include new venting), losing heat $100 to $750, scaling $150 to $450, rust $200 to $2,000. Plumbers $50 to $150 per hour, call-out fee around $50, emergency surcharge $100 to $200, maintenance visit $100 to $250, earthquake straps $100 to $200, disposal $25 to $50. A new heater is listed at $600 to $1,500, and a repair quote of $1,000 or more may favor replacement. Also on the page: solar repairs $150 to $900; pilot light repair $75 to $175; thermostat repair $75 to $150; tank repair $250 to $1,000; by problem, no power $50 to $400, too much pressure $75 to $350, low pressure $75 to $500, clogged $150 to $400, noise $150 to $600, frozen pipes $200 to $550, bad smell $200 to $600. Quoted: "Most water heaters last around eight to ten years. If your unit is getting old, the time might be right to replace it"; "On younger heaters, however, getting repairs might be the better choice"; a thermostat replacement "can usually be completed in under an hour"; the manufacturer warranty "usually covers both the tank and any replacement parts".

Page date Read
What is Roof Decking and Why Does it Matter?FixrAggregated Survey

Roof decking as published (January 24, 2023): panels $2.27 to $4.13 per sq ft (OSB toward the lower end, premium plywood toward the higher end); labor $0.89 to $1.62 per sq ft; for 1,000 sq ft, $2,270 to $4,130 for panels plus $889 to $1,619 for labor, $3,160 to $5,749 in total;

Show all figures from What is Roof Decking and Why Does it Matter?

plank decking "tends to be very expensive to install". Signs of failing decking: roof leaks, wall or ceiling stains, mold or water damage on rafters, sagging, rotten boards.

Page date Read
How Much Does The Average Furnace Repair Cost? (2026)Forbes HomeIndependent Trade Publication

Furnace repair costs as published: ignitor $150 to $250 for replacement; circuit board $75 to $200 for repair and up to $600 for replacement; draft inducer motor $200 to $500 for repair and up to $1,500 for replacement.

Show all figures from How Much Does The Average Furnace Repair Cost? (2026)

Heat exchanger replacement up to $1,500 and repair $100 to $200. The page does not publish a whole-furnace replacement range or an age-times-repair-cost rule, and carries an audit stamp of April 18, 2024.

Page date Read
Blower Motor Replacement Cost in 2026HomeGuideAggregated Survey

Blower motor replacement as published: $500 to $2,300 average replacement cost (part and labor).

Page date Read
How Much Does a New Roof Cost? (Roof Replacement Cost)HomeGuideAggregated Survey

Roof replacement as published (page dated November 7, 2025; cost data from research and project costs reported by HomeGuide members): $5,700 to $16,000 on average;

Show all figures from How Much Does a New Roof Cost? (Roof Replacement Cost)

for an asphalt shingle roof $10,800 national average, $2,700 minimum, $26,800 maximum, $5,700 to $16,000 average range; $300 to $600 per square installed; per square: old roof removal $100 to $300, materials $100 to $250, replacement labor $200 to $350, total $400 to $900; "Roofing labor costs $1.50 to $3.00 per square foot or $150 to $300 per square on average to install shingles"; by house size (single story, 6:12 pitch) 1,000 sq ft house (1,120 sq ft roof) $3,500 to $6,700, 1,500 (1,675) $5,000 to $10,100, 2,000 (2,235) $6,700 to $13,400, 2,500 (2,795) $8,500 to $16,800, 3,000 (3,355) $10,100 to $20,100, 3,500 (3,915) $11,700 to $23,500; installed per sq ft asphalt $3 to $6 ($7,500 to $14,000), 3-tab $3 to $5, architectural $4 to $6, luxury asphalt $5 to $7, metal $5 to $16, tile $7 to $25, wood shakes $7 to $15, slate $10 to $30; permits $100 to $500; tear-off $1 to $5 per sq ft (shingles or metal $1 to $3); decking $2 to $5 per sq ft installed; "Most cities limit roofs to a maximum of two roof layers"; garage, townhouse and mobile home rows; "Replacing a roof takes 1 to 8 days", asphalt shingles 1 to 3 days, metal 1 to 5, wood shakes or slate 6 to 8, and rain, snow, heavy wind or temperatures below 40 F delay installation; "Most homeowners insurance policies cover roof replacement for damage resulting from an accident or natural disaster. Homeowners insurance does not cover normal wear and tear due to age"; repair instead if less than 25% of the roof is damaged, repairs cost less than 30% of a new roof and the roof is under 20 years old.

Page date Read
Metal Roof Cost in 2026: Material & Installation PricingHomeGuideAggregated Survey

Metal roof installed costs as published (page dated November 21, 2025): $5 to $16 per square foot installed; $7,500 to $40,000 average range; $23,800 national average, $5,000 minimum and $56,000 maximum;

Show all figures from Metal Roof Cost in 2026: Material & Installation Pricing

by roof size 1,000 sq ft $5,000 to $16,000, 1,500 $7,500 to $24,000, 2,000 $10,000 to $32,000, 2,500 $12,500 to $40,000, 3,000 $15,000 to $48,000, 3,500 $17,500 to $56,000; corrugated $5 to $12, standing seam $9 to $16, tin $6 to $18, galvanized or Galvalume steel $5 to $13 per sq ft installed; labor $4 to $8 per sq ft ($400 to $800 per square); removing an existing roof $1 to $3 per sq ft, and installing over the existing roof "saves time, labor, and disposal fees but may add too much weight or make underlying damage unrepairable"; installation takes 2 to 5 days on average; lifespan 30 to 80+ years.

Page date Read
Roof Repair Cost in 2026: Minor to Major Repair PricingHomeGuideAggregated Survey

Roof repair costs as published (page dated February 9, 2026): $150 to $1,000 for minor repairs (minor leaks, a few shingles), $1,000 to $3,000 for moderate repairs (leak and water damage, replacing a 10 ft by 10 ft shingle area) and $3,000 to $6,000+ for major repairs;

Show all figures from Roof Repair Cost in 2026: Minor to Major Repair Pricing

"Most roofers have a $150 to $300 minimum call-out fee for repairs"; emergency repair $200 to $300 extra; inspection $100 to $400; by repair: vent boot $75 to $150, vent replacement $200 to $700, valley replacement $200 to $850, flashing repair $200 to $500, missing shingles $100 to $300 (up to 25 shingles), sagging roof $1,000 to $5,000, roof deck repair $200 to $500 per 100 sq ft; insurance: "You may be able to file a claim if a covered event caused the roof damage", and leaving damage unrepaired may void coverage for resulting rot and mold.

Page date Read
Roofing Labor Cost per Square Foot and per SquareHomeGuideAggregated Survey

Roofing labor as published (page dated November 7, 2025): "Roofing labor costs $2.00 to $3.50 per square foot on average or $200 to $350 per square to install shingles, not including materials and supplies";

Show all figures from Roofing Labor Cost per Square Foot and per Square

asphalt shingles $200 to $300 per square and architectural or dimensional shingles $300 to $350 per square for labor; metal $400 to $800 per square ($4 to $8 per sq ft); labor for a shingle roof by roof size 1,000 sq ft $2,000 to $3,500, 1,500 $3,000 to $5,300, 2,000 $4,000 to $7,000, 2,500 $5,000 to $8,800, 3,000 $6,000 to $10,500, 3,500 $7,000 to $12,300; "Roofers charge $30 to $100 per hour"; labor makes up 50% to 70% of a roof replacement; old roof removal $100 to $300 per square ($1 to $5 per sq ft depending on material); decking $2 to $5 per sq ft installed; a roof-over (overlay) "saves on removal costs but may reduce the roof's lifespan", and most cities limit roofs to two layers; "The peak season for roofing is late spring to fall. Roofing done during the off-season is typically cheaper but may take longer due to extreme cold or inclement weather"; labor prices typically rise after widespread storm damage; a pitched roof's area is typically 15% to 40% larger than the floor area.

Page date Read
Sewer Line Repair & Replacement Cost in 2026HomeGuideAggregated Survey

Sewer line costs as published: $50 to $250 per linear foot to replace; $2,000 to $10,000 average total replacement (40 linear feet); $150 to $3,800 average repair.

Page date Read
Standing Seam Metal Roof CostHomeGuideAggregated Survey

Standing seam metal roof as published (page dated April 5, 2023): $9 to $16 per sq ft installed; $13,500 to $40,000 average range, $22,300 national average, $9,000 minimum, $56,000 maximum;

Show all figures from Standing Seam Metal Roof Cost

by roof size 1,000 sq ft $9,000 to $16,000, 1,500 $13,500 to $24,000, 2,000 $18,000 to $32,000, 2,500 $22,500 to $40,000, 3,000 $27,000 to $48,000, 3,500 $31,500 to $56,000; installed steel $8 to $13, Galvalume $7.50 to $12.50, aluminum $9.50 to $17, zinc $10 to $20, copper $18 to $32 per sq ft; labor $5 to $8 per sq ft; removing an old roof $1 to $3+ per sq ft; "Installing a standing seam roof takes 2 to 5+ days".

Page date Read
Tankless Water Heater Installation Cost in 2026HomeGuideAggregated Survey

Tankless water heater costs as published: $1,400 to $5,600 average cost with installation. Natural gas models installed $2,100 to $5,600, covering the unit, labor and needed modifications; no tank-to-tankless conversion total is published.

Page date Read
Water Line Replacement Cost in 2026HomeGuideAggregated Survey

Water line costs as published: $50 to $200 per linear foot trenched; $70 to $250 per linear foot trenchless; $2,000 to $5,000 average total for a main water line.

Page date Read
NRCA Roofing Manual: Steep-slope Roof Systems (Asphalt Shingle Application)National Roofing Contractors Association (NRCA)Industry Trade Association

Roofing square definitions (1 square = 100 sq ft), slope/pitch waste allowances (10% to 15%), underlayment requirements, and flashing installation standards.

Page date Read
How Long Does Ductwork Last?OnOttoIndependent Trade Publication

Duct lifespan as published (August 2026): flexible ducts 10 to 25 years; galvanized sheet metal 30 to 50 years or more; well-sealed and insulated ducts 40 to 50 years. A plumbing supply retailer page also lists 15 to 25 years for flexible ducts.

Page date Read
2025 Cost vs. Value Report: National AveragesRemodeling / Journal of Light ConstructionIndependent Trade Publication

National average job cost for 28 remodeling projects, including roofing replacement with asphalt shingles ($31,871; 68% cost recouped) and metal ($51,865; 50% cost recouped).

Page date Read
Residential Tankless Water Heater Sizing & Specification Engineering GuideRinnai America CorporationManufacturer Documentation

Condensing tankless unit specifications, flow rate sizing (6.5 to 11.0 GPM), gas supply requirements (199,000 BTU max, 3/4-inch gas line), direct coaxial venting specs, and commercial/residential warranties.

Page date Read
Home Depot retail price: American Standard Cadet PRO two-piece toilet (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Equipment price for an American Standard Cadet PRO 2-piece, 1.28 GPF, standard height round toilet with 12 in. rough-in, model 215DA104.020: $232.90. Fixture only; installation, seat and wax ring are separate or not confirmed.

Page date Read
Home Depot retail price: Charlotte Pipe 4 in. PVC DWV repair coupling (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Material price for a Charlotte Pipe 4 in. PVC DWV repair coupling, model PVC001301200HD: $20.87. Coupling only; installation and solvent cement are separate.

Page date Read
Home Depot retail price: Everbilt 1/3 HP aluminum sump pump (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Equipment price for an Everbilt 1/3 HP aluminum sump pump with a vertical float switch, model HDPS33V: $131.72. Pump only; installation, basin and backup are separate.

Page date Read
Home Depot retail price: Everbilt reinforced toilet wax ring with bolts (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Material price for an Everbilt reinforced toilet wax ring with plastic horn and zinc-plated bolts, model 4301-SP: $5.98 per kit. Material only; installation is separate.

Page date Read
Home Depot retail price: Glacier Bay TurboGrind 1/2 HP continuous feed garbage disposal (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Equipment price for a Glacier Bay TurboGrind 1/2 HP continuous feed garbage disposal with power cord, model 10-US-GB500: $129.00. Unit only; installation, accessories, removal and permits are separate.

Page date Read
Home Depot retail price: HOME-FLEX 1/2 inch x 25 ft CSST gas pipe (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Material price for a HOME-FLEX 1/2 inch by 25 ft CSST gas pipe, model 11-00525: $56.85, about $2.27 per foot. Pipe only; connectors, installation and other components are separate.

Page date Read
Home Depot retail price: JM EAGLE 4 in. x 10 ft PVC sewer and drain pipe (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Material price for a JM EAGLE 1610 PVC D2729 sewer and drain pipe, 4 in. x 10 ft: $31.53 per length, also listed at $3.15 per foot, from the category listing. Pipe only; cement, primer, excavation and installation are separate.

Page date Read
Home Depot retail price: Rheem 3 ton cased evaporator coil (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Equipment price for a Rheem 3 ton cased coil, model RCF3617STAMCA: $1,128.96. Coil only; installation is separate.

Page date Read
Home Depot retail price: ROYALTON 88,000 BTU 80% AFUE gas furnace (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Equipment price for a ROYALTON 88,000 BTU, 80% AFUE, single-stage gas furnace with blower, model 80G1UH090BE16: $1,537.40. Equipment only; installation, ductwork, permits and gas line are separate.

Page date Read
Home Depot retail prices: OSB sheathing and GAF Timberline HDZ shingles (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

7/16 in. OSB 4 ft by 8 ft sheathing panel $14.51 per sheet; GAF Timberline HDZ Weathered Wood shingles $44.97 per bundle (33.33 sq ft), about $135 per roofing square. Materials only, not installed cost.

Page date Read
Home Depot retail prices: Rheem 50-gallon water heaters (observed 2026-10-09)The Home Depot (retail product listings)Retail listing

Equipment prices for 50-gallon Rheem water heaters: natural gas XG50T06EC38U1 $719; electric XE50T06ST45U1 $599 and XE50M06ST45U1 $619; hybrid heat pump XE50T10H45U1 $1,699. Equipment only, not installed cost.

Page date Read
Air Conditioner Repair Cost (2026 Pricing)This Old HouseIndependent Trade Publication

AC repair as published: $100 to $1,000 overall, most homeowners $150 to $650; diagnostic fee $75 to $150; capacitor $150 to $400; thermostat $100 to $500; drain line cleaning $80 to $250; refrigerant leak repair $200 to $1,500+; relay or contactor $100 to $450;

Show all figures from Air Conditioner Repair Cost (2026 Pricing)

fan motor $300 to $800; compressor $1,000 to $3,000+; evaporator coil $700 to $2,500+; condenser coil $1,000 to $2,700+; circuit board $200 to $800; refrigerant line set $200 to $700; drain pan $200 to $800; ductless mini-split repair $250 to $900. Replace rather than repair if the AC is over 10 years old and repair cost times age exceeds $5,000; other signs: a repair over 50% of the price, frequent breakdowns, more than 12 years old, or R-22. Central unit replacement $2,500 to $15,000 installed; systems last 12 to 15 years.

Page date Read
All About Furnace Replacement: Cost and When to Do ItThis Old HouseIndependent Trade Publication

Furnace replacement as published (updated 05/25/2026): $4,771 average; $2,825 to $6,846 range; total replacement by type electric $2,000 to $7,000, natural gas $3,800 to $10,000, propane $3,000 to $6,000, oil $6,750 to $10,000;

Show all figures from All About Furnace Replacement: Cost and When to Do It

furnace unit only electric $500 to $1,100, gas $800 to $2,800, propane $900 to $5,000, oil $1,900 to $3,100. After about 15 years, with frequent repairs, consider replacement; warning signs include a cracked heat exchanger, rising bills, uneven heat and frequent repairs; get a second opinion when needed. Also published: the $2,825 to $6,846 range is credited to HomeAdvisor; dust, soot or rust from the furnace (especially around the register) is a replacement sign; late spring or early summer is usually the cheapest time to replace; most furnaces last 20 to 30 years, with replacement considered after about 15.

Page date Read
Central AC Replacement Cost Guide (Condenser & Evaporator Coil Systems)This Old HouseIndependent Trade Publication

Central AC costs as published (2026 survey): $6,345 low, $8,460 average, $10,575 high; $16,759 average for a full system installation across unit types. Also published: a 2,000 sq ft home $9,323 and a 2,500 sq ft home $12,600 on average; average AC repair $743;

Show all figures from Central AC Replacement Cost Guide (Condenser & Evaporator Coil Systems)

ductless mini-split system $8,221; replacement recommended under the 50% rule (a repair costing more than half of a new model); air conditioners can last 15 to 20 years when maintained; 72% of homeowners who replaced their central air conditioners paid between $100 and $250 per hour; by tonnage averages $8,448 (1.5 tons) to $16,312 (5 tons); by brand $6,572 (American Standard) to $10,069 (Lennox); says the EPA banned older refrigerants like R-22.

Page date Read
Evaporator Coil Replacement Cost (2026 Guide)This Old HouseIndependent Trade Publication

Evaporator coil replacement as published (updated 04/06/2026, Alexis Carthan): low $267, average $1,350, high $2,702; text says $627 to $2,700 in most cases. By AC size (low / average / high): 2 ton $550 / $1,250 / $2,000; 2.5 ton $650 / $1,400 / $2,100;

Show all figures from Evaporator Coil Replacement Cost (2026 Guide)

3 ton $700 / $1,550 / $2,350; 3.5 ton $750 / $1,650 / $2,500; 4 ton $800 / $1,700 / $2,600; 5 ton $900 / $1,800 / $2,700. By coil type: A-coil $1,300, N or Z coil $1,550, slab $1,200. Warm air from the vents after lowering the thermostat can mean a faulty coil; under warranty you mainly pay for labor and materials; local permit and inspection requirements can add cost; schedule replacement in late fall or early spring; repair when the cost is under 30% of a full replacement and the system is under 10 years old; small pinhole leaks may be soldered or sealed, extensive or multiple leaks usually mean replacement; choose a coil compatible with the system's refrigerant and matched to the outdoor unit's tonnage; an outdated refrigerant such as R-22 is a reason to consider replacing the system.

Page date Read
Furnace Blower Motor Replacement CostThis Old HouseIndependent Trade Publication

Furnace blower motor as published: $170 to $2,400 for the motor itself (1/4 hp $100 to $550; 1 hp $250 to $2,000) plus $150 to $250 for professional installation labor.

Show all figures from Furnace Blower Motor Replacement Cost

Also published: average motor cost by horsepower 1/4 hp $325, 1/3 hp $450, 1/2 hp $560, 3/4 hp $838, 1 hp $1,125; PSC about $575 and ECM about $875; single-speed $600, multi-speed $710, variable-speed $1,050; repair parts on average: capacitor $30, ECM module $520, ECM repair kit $45, blower wheel $163, bearing $98, belt $53, housing $198. Replacement usually takes one to three hours. Signs: weak or no airflow, rattling, squealing or screeching noises, overheating with a burning smell, frequent shutdowns. Most warranties cover blower motor parts but not installation; DIY can void the warranty and is not recommended. Contractors often charge higher rates in winter. The furnace model determines which motor types it can support.

Page date Read
Heat Pump Cost Guide (2026 Pricing)This Old HouseIndependent Trade Publication

Heat pump costs as published (page updated 10/14/2026, read 2026-11-09; 2026 survey of 1,000 homeowners): $8,042 average installed cost for a central heat pump;

Show all figures from Heat Pump Cost Guide (2026 Pricing)

replacement table: single-zone mini-split $3,250, whole-home air-source $8,007, air-to-water $6,719, geothermal $17,000 for a small or medium home and $30,000+ for a large home; about $12,000 on average for a 2,000 sq ft home (3 to 5 tons), over $20,000 for a top-tier model; premium central units for large homes can exceed $30,000; average equipment cost by brand from $4,550 (Ruud) to $9,550 (Trane); repair averages air-source $798, geothermal $1,500; about 68% of surveyed owners repaired and 32% replaced; 58% of owners who replaced a heat pump paid $150 or more per hour for installation labor; about 11% of those who replaced reported permitting delays; cold-climate models with enhanced compressors and higher heating capacities typically cost more than standard models (no figure); lifespan about 15 years per local installers; replacement signs: age, poor performance, frequent costly repairs, home expansion.

Page date Read
How Much Does a New Roof Cost in 2026? Complete Cost GuideThis Old HouseIndependent Trade Publication

Roof costs as published (2026 homeowner survey; the page credits its material cost data to Homewyse; page updated 10/07/2026): $10,319 average for a 2,000 sq ft asphalt shingle roof ($5.16 per sq ft); $29,909 average across all roofing materials for a 2,000 sq ft roof;

Show all figures from How Much Does a New Roof Cost in 2026? Complete Cost Guide

52% of surveyed homeowners paid $5,001 to $20,000; labor about 65% of project cost; roofer labor about $75 per hour. A generic table lists asphalt shingles at $5.16 per sq ft and metal at $19.30 per sq ft ($10,319 and $38,593 for a 2,000 sq ft roof); no per-sq-ft figure for architectural shingles or standing seam alone. Wood shake $26,302 ($13.15 per sq ft) and clay tile $44,423 ($22.21 per sq ft) for 2,000 sq ft; asphalt totals by roof size 1,000 sq ft $5,160, 1,500 $7,740, 2,000 $10,320, 2,500 $12,900, 3,000 $15,480; metal totals by roof size 1,000 sq ft $19,300, 1,500 $28,950, 2,000 $38,600, 2,500 $48,250, 3,000 $57,900; lifespans asphalt 30 to 35 years, wood shake 30 to 50, metal 40 to 70, clay tile 50 to 100, slate 75 to 150, concrete tile "often lasting 50 years or more"; labor 65% of total project costs and about $75 per hour (Roofers Guild); areas with higher living costs or a shortage of skilled roofers may have higher labor rates; many manufacturers require professional installation to honor their warranty; recommends replacing a roof more than 15 years old with widespread damage and repairing one under 10 years old with localized issues; replacement signs listed: extensive surface damage, leaks, moisture issues, structural issues and a roof older than 15 years. Also published: "Replacing a roof can take one day to a week or longer, depending on the scope of the job", and 46% of surveyed homeowners said the project took three to seven days; spring and winter are "often the best times" because contractors have fewer projects and may charge lower rates; "Your homeowners insurance policy might cover repair or replacement costs" when damage comes from severe weather or fallen trees; permits may be needed depending on local codes and are usually an extra cost (no dollar figure); steep roofs and roofs with multiple valleys and dormers cost more (no dollar figure). No dollar figures for tear-off, permits or decking.

Page date Read
How Much Does a Split AC Installation Cost? (2026 Pricing)This Old HouseIndependent Trade Publication

Split AC installation as published: $2,000 low, $11,000 average, $22,000 high. By number of zones (range, average): 1 zone $500 to $5,000 ($2,750); 2 zones $1,400 to $7,700 ($4,550); 3 zones $1,800 to $9,100 ($5,450); 4 zones $2,600 to $10,700 ($6,650);

Show all figures from How Much Does a Split AC Installation Cost? (2026 Pricing)

5 zones $4,400 to $12,000 ($8,200). By size: 0.75 ton (9,000 BTU) $3,000 to $4,200; 1 ton (12,000 BTU) $3,500 to $5,000; 2 tons (24,000 BTU) $6,000 to $8,000; 3 tons (36,000 BTU) $8,000 to $11,000; 4 tons (48,000 BTU) $12,000 to $15,000; 5 tons (60,000 BTU) $15,000 to $18,000. Ductless mini-split replacement averaged $8,221 in its survey; 72% paid $150 per hour or more in labor. Also published: some installations require panel upgrades, new circuits or local permits to meet code; scheduling installation in spring or fall can lead to better pricing.

Page date Read
How Much Does AC Condenser Replacement Cost?This Old HouseIndependent Trade Publication

AC condenser (outdoor unit) replacement as published: $1,200 to $4,200, $2,700 average; under warranty, installation only $300 to $1,200. Materials and installation by tonnage: 1.5 tons $1,200 to $2,300; 2 tons $1,300 to $2,500; 2.5 tons $1,350 to $2,900;

Show all figures from How Much Does AC Condenser Replacement Cost?

3 tons $1,400 to $3,100; 3.5 tons $1,500 to $3,400; 4 tons $1,600 to $3,700; 4.5 tons $1,750 to $3,950; 5 tons $1,900 to $4,200. Material costs: compressor $1,000 to $2,500, condenser coil $850 to $2,700, full condenser unit $850 to $3,000. Labor $75 to $125 per hour. Replacing the entire system may be more cost-effective for units more than 10 to 15 years old.

Page date Read
How Much Does Air Duct Cleaning Cost? (2026 Pricing)This Old HouseIndependent Trade Publication

Air duct cleaning as published: $450 to $1,000 typical; $0.15 to $0.40 per sq ft; supply vents $25 to $50 each, return vents $40 to $75 each;

Show all figures from How Much Does Air Duct Cleaning Cost? (2026 Pricing)

by home size 1,200 sq ft $180 to $480, 1,500 sq ft $225 to $600, 2,000 sq ft $300 to $800, 2,500 sq ft $375 to $1,000, 3,000 sq ft $450 to $1,200; mold lab testing $50 to $700. Warns about suspiciously low per-vent prices, undisclosed whole-house fees and add-on charges for coils, grilles and drip pans.

Page date Read
How Much Does Air Duct Replacement Cost? (2026 Pricing)This Old HouseIndependent Trade Publication

Air duct replacement as published: $16 to $19 per linear foot; an average 200-foot replacement about $3,100 to $3,700; under $2,000 for a small project to more than $8,000 for a large or complex system. By length: 100 ft $1,600 to $1,900; 200 ft $3,100 to $3,700;

Show all figures from How Much Does Air Duct Replacement Cost? (2026 Pricing)

300 ft $4,700 to $5,600; 400 ft $6,200 to $7,500; 500 ft $7,800 to $9,300. Materials only per linear foot: flexible non-insulated $1 to $3, flexible insulated $2 to $4, fiberboard $4 to $7, sheet metal $7 to $15. Permits from under $100 to several hundred dollars; asbestos or mold remediation upwards of $2,000. Repair is practical for systems under 10 years old with minor damage. Lifespan: flexible 10 to 20 years, fiberboard 10 to 15, sheet metal 20 or more; replacement after roughly 10 to 15 years as a rule of thumb. Also published: a basic system with a simple layout takes 1 to 2 days, a large and complex one four days or more; signs for replacement are extensive air leaks, significant corrosion or damage, poor airflow or uneven temperatures in several rooms, poor design or installation, major insulation failures and aging ducts that need frequent repairs; homeowners insurance generally does not cover replacement for age or wear and tear, but may after sudden damage such as extreme weather or fire; duct leakage can account for 20% or more of heating and cooling energy loss (quoted expert).

Page date Read
How Much Does an AC Compressor Cost to Replace? (Parts & Labor Analysis)This Old HouseIndependent Trade Publication

AC compressor replacement as published: $1,550 average including parts and labor; by tonnage $1,050 (1.5 to 2 tons), $1,500 (2.5 to 3 tons), $1,600 (3.5 to 4 tons); compressor part about $1,038 on average.

Show all figures from How Much Does an AC Compressor Cost to Replace? (Parts & Labor Analysis)

Also published: low/average/high by tonnage $700/$1,050/$1,400 (1.5 to 2 tons), $900/$1,500/$2,100 (2.5 to 3 tons), $1,100/$1,600/$2,100 (3.5 to 4 tons); compressor repair $931 on average; type averages reciprocating $700, scroll $1,000, centrifugal $2,000; compressor unit alone $950 or more; labor $113 an hour or an average flat fee of $600; extended warranty $200 to $400; prices vary by as much as $800 for the same job in the same area. Repair-or-replace guidance: replacing the compressor is worth it if the system is under 10 years old and the repair costs less than $1,000; above $1,000, or past 12 to 15 years, or over 50% of a new unit, a full AC replacement is often the better choice; R-22 systems are listed under replacement recommended. Also on the page (read 2026-11-09, Alexis Carthan): signs of a failing compressor are warm air from the vents, loud noises, hard starts, tripped circuit breakers and an outdoor unit that will not turn on; in its homeowner survey most repairs took 8 hours or less, 47% reported 2 to 4 hours, and 78% paid $100 or more per hour; schedule replacement in the off-season, late fall to early spring; federal regulations phase out refrigerants with higher global warming potential.

Page date Read
How Much Does HVAC Installation Cost? (2026 Pricing)This Old HouseIndependent Trade Publication

HVAC installation as published: $5,000 to $12,500 for a standard-efficiency system with a simple duct layout, over $22,000 for larger homes with premium equipment. Equipment only, excluding ductwork: air conditioner $4,000 to $8,000; heat pump $4,200 to $7,600;

Show all figures from How Much Does HVAC Installation Cost? (2026 Pricing)

air-source heat pump $4,500 to $8,000; ductless mini-split AC $1,500 to $4,000; ductless mini-split heat pump $1,300 to $8,000; geothermal $6,000 to $20,000; furnace $2,000 to $10,000. Averages by home size including ductwork and thermostat: 1.5 tons/1,000 sq ft $8,138; 2 tons/1,200 sq ft $8,241; 3 tons/1,800 sq ft $8,344; 4 tons/2,500 sq ft $12,670; 5 tons/3,000 sq ft about $17,100. Ductwork $1,000 to $2,700 for a 1,000 sq ft system. Air conditioners and heat pumps last 10 to 15 years, furnaces 15 to 20 or more; systems over 15 years old may use outdated refrigerants.

Page date Read
How Much Does It Cost to Pump a Septic Tank? (2026 Pricing)This Old HouseIndependent Trade Publication

Septic tank pumping as published: $420 average, typical $290 to $560, about $0.23 to $0.40 per gallon. By tank size: 750 gal $175 to $300, 1,000 gal $225 to $400, 1,250 gal $275 to $500, 1,500 gal $345 to $600, 1,750 gal $400 to $700.

Show all figures from How Much Does It Cost to Pump a Septic Tank? (2026 Pricing)

By city: Minneapolis $180 to $280, Milwaukee $250 to $320, Concord NH $260 to $330, Denver $260 to $350, Phoenix $360 to $600, Portland OR $440 to $750. Buried or hard-to-reach access adds $50 to $200; thick sludge from skipped pumping adds $100 to $300. Camera inspection $250 to $500; system inspection $250 to $1,180; outlet filter cleaning $100 to $200; baffles $300 to $500; riser $300 to $1,000; distribution box $600 to $1,300; overflow cleanup $7 to $15 per sq ft; new septic system $20,000 to $50,000. Pumping every 3 to 5 years. Quoted: "The job typically takes 2–3 hours based on your tank size and waste volume"; "Most 1,000-gallon tanks serving a family of four need pumping every 3–5 years"; "Book your tank pumping during the winter, which is typically the slow season, for discounts"; signs: slow drains or gurgling pipes, and backups need immediate pumping.

Page date Read
How Much Does Sewer Line Replacement Cost? (2026 Pricing)This Old HouseIndependent Trade Publication

Sewer line replacement as published: $3,320 average, most homeowners pay $1,390 to $5,320. Traditional excavation $50 to $200 per linear foot, trenchless $60 to $250 per linear foot (pipe bursting and lining are not priced separately).

Show all figures from How Much Does Sewer Line Replacement Cost? (2026 Pricing)

Materials (Angi estimates quoted by the page): PVC $120 to $320, ABS $120 to $440, cast iron $800 to $3,000 for 40 feet, copper $1,200 to $3,200. Camera inspection $100 to $500, plumber $150 to $500 per hour, permits $100 to $1,000, excavation $400 to $1,200 or more, drain line cleaning $75 to $200, tree root removal $80 to $1,000, landscaping $4.50 to $12 per sq ft, yard leveling $1 to $2 per sq ft, concrete repair $1 to $20 per sq ft. The page states: "The cost data featured in this guide is based on estimates from Angi, unless otherwise noted." Quoted: a sign is when "multiple drains in your home are slow or frequently back up"; "Review your homeowners insurance or consider a sewer line warranty to see if any portion of the replacement may be covered"; "Scheduling your project in late fall or winter may result in lower labor rates and better availability".

Page date Read
How Much Does Sump Pump Installation Cost? (2026 Guide)This Old HouseIndependent Trade Publication

Sump pump installation as published: $1,400 average; most homeowners pay $500 to $4,000; a new submersible pump and pit with above-ground drainage about $1,400; installation in an existing basin can cost as little as $500;

Show all figures from How Much Does Sump Pump Installation Cost? (2026 Guide)

replacement typically $350 to $1,000 including materials and labor. Labor $300 to $4,000 (basin labor alone $500 to $1,200, not including concrete drilling); plumbers $75 to $150 per hour. Unit prices: pedestal $80 to $800, submersible $90 to $1,000, backup battery only $150 to $250, water-powered backup $200 to $900. Discharge pipe above ground $150 to $400, buried $250 to $2,000; drilling through concrete $2,500 to $5,000. Also: primary pump with backup battery $150 to $2,000, combination system $500 to $1,500; average pump price by horsepower (unit only) 1/3 HP $90 to $250, 1/2 HP $160 to $400, 3/4 HP $200 to $500. Quoted: "Pedestal sump pumps last up to 30 years when properly maintained"; "Submersible pumps must be replaced every five to 15 years"; "No, homeowners insurance does not typically cover sump pump replacement", unless the pump was damaged in a covered incident; without a backup a basement "may be at risk of flooding during a power outage". Signs listed: pump running constantly, frequent cycling, unusual noise or vibration, rust or corrosion, water in the motor housing.

Page date Read
How Much Does Water Heater Installation Cost? (2026)This Old HouseIndependent Trade Publication

Water heater installation as published: $1,600 to $5,400 typical across all unit types, $1,950 average (attributed to The Home Depot); basic tank models from $1,200 installed; tankless about $2,800 average.

Show all figures from How Much Does Water Heater Installation Cost? (2026)

Tank: $1,200 to $2,300 installed, unit $600 to $1,000, labor $300 to $800, gas venting $300 to $500, water line connections $100 to $200. Tankless: $2,100 to $4,000 installed, unit $1,000 to $2,000, labor $800 to $1,500, gas line $500 to $1,000, electrical upgrades $300 to $800, venting $500 to $1,000. By size: 40 gal $600 to $1,200, 50 gal $700 to $1,800, 75 gal $900 to $2,300, 80 gal $1,000 to $3,000. Heat pump $2,500 to $3,500. Plumbers $40 to $200 per hour. Extras: attic installation $200 to $1,000, garage freeze protection $100 to $300, closet ventilation $200 to $800, power venting $300 to $600 plus $300 to $500 electrical, direct venting $500 to $1,000, basic gas venting $300 to $500, chimney liner $500 to $700, expansion tank $40 to $150, earthquake strapping $100 to $300, drainage $50 to $200, T&P relief valve $20 to $200, new gas or electric lines when switching fuel $1,500 to $2,000 (gas lines when converting from electric $1,500 to $2,300), removal and disposal $100 to $300, permits and inspections $50 to $200, site preparation $100 to $500, water line changes $200 to $600, emergency or after-hours service $200 to $500, water damage repair $500 to $2,500, system flush $100 to $250. Pacific Northwest prices can run up to 45% above the $1,950 national average; Gulf Coast 10% to 20% above; Mid-Atlantic and Midwest about 5% to 10% below; South Florida 20% below. Unit prices before installation: electric about $850, gas about $800 plus venting, propane from $700 before tank installation. Sizing: 1 to 2 people 30 to 40 gal, 2 to 3 people 40 to 50 gal, 3 to 4 people 50 to 60 gal, five or more 75 gal or more. Quoted on the page: "Standard tank installations usually take 1–3 hours, while tankless systems need 4–6 hours" for complete setup; "Consider replacement when your unit reaches 10 years old, produces rusty water, or fails to meet your hot water demands"; "Most jurisdictions require installation permits for water heaters, especially for fuel type changes or venting modifications"; replacing the unit before it fails avoids emergency rates.

Page date Read
Sewer Line Repair and ReplacementThis Old HouseIndependent Trade Publication

Sewer line work as published: about $5,000 national average for replacement (estimates from Angi and HomeGuide); $50 to $250 per linear foot; digging a trench adds $30 to $70 per cubic foot. Total by length: 25 to 35 ft $1,250 to $8,750; 35 to 45 ft $1,750 to $11,250;

Show all figures from Sewer Line Repair and Replacement

45 to 55 ft $2,250 to $13,750; 55 to 65 ft $2,750 to $16,250; 65 to 75 ft $3,250 to $18,750; 75 to 100 ft $3,750 to $25,000; 100 to 125 ft $5,000 to $31,250. Quoted: "On average, you can expect a sewer line repair to take anywhere from one to five days"; "It's unlikely that homeowners insurance will cover the repair costs unless another party or a natural disaster damaged your sewer line"; if the city is at fault, "they should cover any repairs that are needed"; signs: "A blockage in the main sewage line is the likely culprit if multiple draining areas in your home are clogged" and a broken pipe "will quickly pool water that seeps through the grass"; causes listed: tree roots, non-flushable items, corrosion and extreme temperatures.

Page date Read
Standing Seam & Metal Roofing Cost Guide (2026 Pricing)This Old HouseIndependent Trade Publication

Standing seam metal roof costs as published (page updated 03/31/2026; pricing calculated from RSMeans data, plus a 2026 homeowner survey): $8 to $39 per sq ft; $7,540 low, $23,485 average, and $39,430 high for a 1,000 sq ft roof;

Show all figures from Standing Seam & Metal Roofing Cost Guide (2026 Pricing)

by roof size (low to high) 1,200 sq ft $9,048 to $47,316, 1,500 $11,310 to $59,145, 2,000 $15,080 to $78,860, 3,000 $22,620 to $118,290; labor $2.95 to $10.93 per sq ft; "Nearly all standing seam roof panels come in 24 gauge"; lifespan 50 to 80 years; nearly 56% of surveyed homeowners who installed a metal roof spent $10,000 or more; the roofing company typically pulls the permits.

Page date Read
What Is the Cost of Roof Repair? (2026 Pricing)This Old HouseIndependent Trade Publication

Roof repair as published (updated 03/05/2026): repair card $379 to $1,755; by severity minor $150 to $1,000, moderate $1,001 to $2,000, major $2,001 to $8,000;

Show all figures from What Is the Cost of Roof Repair? (2026 Pricing)

holes and leaks $100 to $1,500, shingle damage $50 to $800, chimney or roof flashing $200 to $500, roof vents $75 to $250, roof valley $300 to $1,000, skylights $300 to $800, fascia and soffits $600 to $6,000, ridge capping $250 to $750, hail damage $700 to $4,000, sagging roof $1,500 to $7,000, dormer $250 to $1,000; inspection $100 to $600; permits $75 to $250; gutter repair $180 to $560; average repair by material: asphalt shingles $975, flat roofing $400, metal (corrugated, standing seam, steel or aluminum shingles) $1,600, slate $1,800, concrete tile $2,400; steep-roof surcharge on a replacement $1,000 to $3,000; "If more than 30% of your roof is substantially damaged, it's time to consider a replacement." Labor was the largest cost factor for 65% of surveyed homeowners.

Page date Read
Occupational Employment and Wage Statistics: Heating, Air Conditioning, and Refrigeration Mechanics and Installers (SOC 49-9021)U.S. Bureau of Labor Statistics (BLS)Federal Labor Bureau

HVAC employee wage observations used to form a regional labor index. May 2025 national figures (retrieved from the BLS Public Data API): 409,670 employed; mean $31.14/hr; median $29.33/hr; 10th to 90th percentile $19.25 to $45.78/hr.

Show all figures from Occupational Employment and Wage Statistics: Heating, Air Conditioning, and Refrigeration Mechanics and Installers (SOC 49-9021)

BLS does not establish contractor billing rates, material prices, equipment prices, or permit fees.

Page date Read
Occupational Employment and Wage Statistics: Plumbers, Pipefitters, and Steamfitters (SOC 47-2152)U.S. Bureau of Labor Statistics (BLS)Federal Labor Bureau

Plumbing employee wage observations used to form a regional labor index. May 2025 national figures (retrieved from the BLS Public Data API): 465,840 employed; mean $34.70/hr; median $30.67/hr; 10th to 90th percentile $21.22 to $52.13/hr.

Show all figures from Occupational Employment and Wage Statistics: Plumbers, Pipefitters, and Steamfitters (SOC 47-2152)

BLS does not establish contractor billing rates, material prices, equipment prices, or permit fees.

Page date Read
Occupational Employment and Wage Statistics: Roofers (SOC 47-2181)U.S. Bureau of Labor Statistics (BLS)Federal Labor Bureau

Roofing employee wage observations used to form a regional labor index. May 2025 national figures (retrieved from the BLS Public Data API): 135,490 employed; mean $27.95/hr; median $26.65/hr; 10th to 90th percentile $18.01 to $39.29/hr.

Show all figures from Occupational Employment and Wage Statistics: Roofers (SOC 47-2181)

BLS does not establish contractor billing rates, material prices, equipment prices, or permit fees.

Page date Read
Occupational Employment and Wage Statistics: Septic Tank Servicers and Sewer Pipe Cleaners (SOC 47-4071)U.S. Bureau of Labor Statistics (BLS)Federal Labor Bureau

Septic servicer employee wage observations. May 2025 national figures (retrieved from the BLS Public Data API): 30,650 employed; mean $25.72/hr; median $23.98/hr.

Page date Read
American Housing Survey 2023: Home Improvement Activity in the Last Two Years (national table)U.S. Census Bureau and HUD, American Housing SurveyFederal Labor Bureau

What U.S. households reported spending on home improvement projects over the previous two years: roofing, 8.3 million projects, median $10,000 and mean $11,610; HVAC, 12.8 million projects, median $5,500 and mean $6,836; interior water pipes, median $1,000 and mean $2,911;

Show all figures from American Housing Survey 2023: Home Improvement Activity in the Last Two Years (national table)

septic tank, median $5,000 and mean $7,945; water heater, dishwasher and garbage disposal combined, median $800 and mean $1,148.

Page date Read
Consumer Furnaces (Appliance and Equipment Standards)U.S. Department of Energy (DOE)Government Agency

DOE has adopted amended standards for non-weatherized gas furnaces and mobile home gas furnaces, with compliance required on and after December 18, 2028; the page lists a Notification of Petition for Rulemaking dated April 27, 2026 (91 FR 22477).

Show all figures from Consumer Furnaces (Appliance and Equipment Standards)

DOE's announcement of September 29, 2023 (energy.gov/articles/doe-finalizes-energy-efficiency-standards-residential-furnaces-save-americans-15-billion) says these furnaces must reach 95 percent AFUE, readily achievable by condensing furnaces, and that the standards were last updated in 2007.

Page date Read
Consumer Water Heaters (standards rulemaking page)U.S. Department of Energy (DOE), Appliance and Equipment Standards ProgramGovernment Agency

Status of the federal water heater standards: compliance with the May 6, 2024 consumer water heater standards "is required on and after May 6, 2029";

Show all figures from Consumer Water Heaters (standards rulemaking page)

the separate December 26, 2024 final rule for gas-fired instantaneous (tankless) water heaters had its effective date delayed and, as of May 20, 2025, "is withdrawn" under a Congressional Review Act notice.

Page date —Read
Energy Conservation Standards for Consumer Water Heaters: Final Rule (EERE-2017-BT-STD-0019)U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable EnergyGovernment Agency

Average installed cost (2022 dollars) from the rule's life-cycle cost tables: gas-fired storage water heaters, 20 to 55 gal: $1,432 baseline, $1,470, $1,578 and $2,241 at higher efficiency levels (Table V.2);

Show all figures from Energy Conservation Standards for Consumer Water Heaters: Final Rule (EERE-2017-BT-STD-0019)

electric storage, 20 to 55 gal: $902 baseline and $1,855 to $1,995 at higher efficiency levels (Table V.8); electric storage, 55 to 120 gal: $2,019 baseline to $2,180 (Table V.10); small electric storage, 20 to 35 gal: $780 baseline (Table V.6). Average lifetime: 14.5 years for gas-fired storage and about 15 years for electric storage water heaters. Rule text: effective July 5, 2024; compliance "required on and after May 6, 2029" for products "manufactured in, or imported into, the United States" from that date; covers all consumer water heaters except gas-fired instantaneous (tankless) models; the adopted level for gas-fired storage water heaters is EL 2, and DOE states that "this final rule does not require a condensing level for gas storage water heaters"; the standards for larger electric storage products "are met through the use of heat pump technology", while electric resistance storage water heaters remain available in the small electric storage class.

Page date Read
Fact Sheet: October 2023 Final Rule - Phasedown of Hydrofluorocarbons: Restrictions on the Use of Certain Hydrofluorocarbons under Subsection (i) of the AIM ActU.S. Environmental Protection Agency (EPA)Government Agency

Maintenance of legacy systems: the rule does not restrict the continued use of existing products or RACHP systems; a product or system may be serviced and repaired throughout its useful life, including replacing components as needed;

Show all figures from Fact Sheet: October 2023 Final Rule - Phasedown of Hydrofluorocarbons: Restrictions on the Use of Certain Hydrofluorocarbons under Subsection (i) of the AIM Act

components needed to repair existing equipment may continue to be manufactured, imported and sold. Increasing the cooling capacity of an existing system, or assembling a system for the first time, counts as a new installation. A banner says EPA issued a reconsideration final rule on May 26, 2026, not yet reflected in the fact sheet.

Page date Read
Lead and Copper Rule Improvements (LCRI): Questions and AnswersU.S. Environmental Protection Agency (EPA)Government Agency

EPA issued the final Lead and Copper Rule Improvements on October 8, 2024. "Approximately 99% of systems are required to replace lead and GRR service lines under their control in 10 years or less", with longer deadlines for a small number of systems;

Show all figures from Lead and Copper Rule Improvements (LCRI): Questions and Answers

the rule also covers certain galvanized service lines; water systems must keep a publicly accessible service line inventory and make replacement plans public; compliance begins three years after the rule's publication (EPA expects late 2027). Homeowner guidance: contact your water utility or a licensed plumber to find out whether the line to your home is lead. EPA's October 2024 LCRI fact sheet (epa.gov/system/files/documents/2024-10/final_lcri_fact-sheet_general_public.pdf, read the same day) adds that the federal government banned new lead pipes in 1986, that up to 9 million homes and businesses are still connected through lead service lines, and that federal infrastructure funds (including $15 billion over five years for lead service line replacement) support replacement projects.

Page date Read
Purchasing and Repairing Home Air-Conditioners or Heat PumpsU.S. Environmental Protection Agency (EPA)Government Agency

HCFC-22 (R-22) phaseout for homeowners (page last updated August 5, 2026): domestic manufacturers may no longer produce new HCFC-22; after 2020 only recycled, reclaimed or previously produced HCFC-22 can be used to service existing equipment;

Show all figures from Purchasing and Repairing Home Air-Conditioners or Heat Pumps

homeowners can continue to have existing units serviced with HCFC-22; there is no EPA requirement to get a new system or convert existing HCFC-22 units; alternative refrigerants will not work well without changes to system components; propane and other unapproved refrigerants are a safety hazard in home AC systems.

Page date Read
Should You Have the Air Ducts in Your Home Cleaned?U.S. Environmental Protection Agency (EPA)Government Agency

EPA guidance (last updated February 19, 2026): EPA does not recommend cleaning air ducts routinely, only as needed; duct cleaning has never been shown to prevent health problems;

Show all figures from Should You Have the Air Ducts in Your Home Cleaned?

consider cleaning when there is substantial visible mold growth inside hard-surface ducts, ducts are infested with vermin, or ducts are clogged with excessive dust and debris or release particles into the home; no chemical biocides are registered for internally insulated duct systems, and biocides should be used only with visible evidence of mold; do not permit sealants except in unusual circumstances; avoid providers that make health claims or push routine cleaning, ask whether they follow NADCA standards, and get written estimates from at least three providers.

Page date Read
Stationary Refrigeration and Air Conditioning (Clean Air Act Section 608)U.S. Environmental Protection Agency (EPA)Government Agency

Section 608 prohibits intentionally venting ODS refrigerants and their substitutes during equipment service or disposal, and links to technician certification and refrigerant recovery, recycling and reclamation programs (page last updated September 3, 2026).

Show all figures from Stationary Refrigeration and Air Conditioning (Clean Air Act Section 608)

Also published: the page does not set an evacuation level in microns and does not name R-410A, R-454B or R-32; for the refrigerant transition see the EPA Technology Transitions entries.

Page date Read
Technology Transitions HFC Restrictions by SectorU.S. Environmental Protection Agency (EPA)Government Agency

AIM Act Technology Transitions restrictions as listed (page last updated August 28, 2026): residential and light commercial air conditioning and heat pump systems (e.g., mini-splits, unitary systems) have a 700 GWP limit with an installation compliance date of January 1, 2025;

Show all figures from Technology Transitions HFC Restrictions by Sector

note 6: no installation compliance date for systems where all specified components were manufactured or imported before January 1, 2025 (Technology Transitions Reconsideration Rule); VRF systems 700 GWP, installation compliance date January 1, 2027; note 5: components used to repair existing systems are not subject to these restrictions.

Page date Read

Government and technical organizations

References for rules, standards and wages

These support how a project works or what rules apply. They are not direct sources of installed prices.

Wage baselineU.S. Bureau of Labor Statistics (BLS)
BLS supports employee wage baselines. It is not, by itself, a source for a contractor’s complete installed price.
Regulations and refrigerantsU.S. Environmental Protection Agency (EPA)
EPA information supports refrigerant rules, certification requirements, and environmental guidance rather than ordinary installed-price ranges.
HVAC technical standardsAir Conditioning, Heating, and Refrigeration Institute (AHRI)
AHRI supports equipment performance and technical standards. It is not a general contractor price source.
Roofing technical informationNational Roofing Contractors Association (NRCA)
NRCA supports roofing practices and technical information. It is not automatically a source for a complete project quote.
Efficiency and appliance informationENERGY STAR and U.S. Department of Energy
ENERGY STAR and DOE support efficiency, appliance, and energy-use information. Those references do not guarantee an installed price.

How these sources become a range is explained in the methodology. To report a broken or outdated source, email contact@repaircostatlas.com.