PlumbingFull System Replacement
Tankless Water Heater Installation & Replacement Cost in 2026: Gas, Electric & Conversion
Tankless water heater installation typically costs $2,100 to $4,000. This Old House average: $2,800.
Cost snapshot
U.S. national figures ·
- Typical range
- $2,100 – $4,000
- This Old House average
- $2,800
- Full range
- $600 – $6,000
Where the typical range comes from: This Old House's published installed range and average for a tankless water heater; the full range is Fixr's $600 to $6,000 for replacing a tankless unit.
Installing a tankless water heater costs $2,100 to $4,000, about $2,800 on average, according to This Old House. Fixr reports $2,500 to $4,500 with a $2,811 average and HomeGuide $1,400 to $5,600; Angi lists $1,400 to $3,900 (Bob Vila's 2023 figures of $1,333 to $3,721 credit Angi and HomeAdvisor). Electric units cost less to install ($1,000 to $3,000 per Fixr) than gas or propane ($1,400 to $3,500). A conversion usually includes work a tank swap does not need: This Old House lists new venting ($500 to $1,000), often a larger gas line ($500 to $1,000) and electrical upgrades ($300 to $800) among the parts of a tankless installation. Replacing an existing tankless unit costs $600 to $6,000 (Fixr).

Overview
Tankless Water Heater Installation Cost: Overview
Tankless water heater installation costs $2,100 to $4,000, about $2,800 on average. Compare gas vs electric, tank-to-tankless conversion, venting and gas line.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $2,100 – $4,000This Old House average: $2,800 | Medium confidence; cited: This Old House, Fixr, Bob Vila, HomeGuide |
| Equipment or materials | $1,000 – $2,000 | Cited: This Old House, Fixr |
| Labor | $800 – $1,500 | Cited: This Old House, Fixr |
By size
Cost by Size & Scope
Plumbing costs scale with tank capacity or flow rate, pipe run length, and how difficult the work area is to reach.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| Electric Tankless (Point-of-Use to Whole-House) | Fixr installed range for electric units, from a single-point unit at the low end (labor $500 – $1,000). Average shown is the calculated midpoint. | $1,000 – $3,000 | $2,000 | Fixr |
| Gas or Propane Tankless | Fixr installed range (labor $900 – $1,500). Average shown is the calculated midpoint. | $1,400 – $3,500 | $2,450 | Fixr |
| Whole-House Tankless, Typical Install | This Old House range and average | $2,100 – $4,000 | $2,800 | This Old House |
By type
Cost by Equipment & Installation Method
| Type | What it involves | Typical cost |
|---|---|---|
| Gas or Propane TanklessWhole-house flow rates | Needs venting and often a larger gas line. Fixr lists $1,400 to $3,500 installed on its tankless page and $1,600 to $4,000 on its gas water heater page. | $1,400 – $4,000 installedFixr |
| Electric TanklessNeeds electrical capacity | No venting or gas line, but usually a dedicated electrical circuit; an electrician bills $65 to $85 per hour (Fixr). | $1,000 – $3,000 installedFixr |
| Single-Point (Point-of-Use)One fixture | A small unit for one sink or shower. Fixr lists the unit at $150 to $300, and its lowest installed example is $1,058 for a single-point 240V electric unit. | Unit $150 – $300Fixr |
| Replacing an Existing Tankless UnitLike-for-like swap | Gas, venting and power are already in place. Fixr lists labor at $135 to $1,200 and a total of $600 to $6,000 depending on the unit. | $600 – $6,000 totalFixr |
Breakdown
Parts vs. Labor Breakdown
What the equipment or materials cost compared with the installer's labor, and what each figure is based on.
Licensed Plumbers & Gasfitters
- Labor range
- $800 – $1,500
- Planning estimate of on-site hours
- 6 – 10 hrs
- BLS median employee wage
- $30.67/hr
- Equipment or materials: $1,000 – $2,000
- The tankless unit, which This Old House lists at $1,000 to $2,000. Fixr lists whole-house units at $450 to $1,500 and gas units with 8+ GPM output at $900 to $2,000, before installation.
- Labor: $800 – $1,500
- Plumber labor for mounting the unit, water and gas connections, venting and startup. This Old House lists $800 to $1,500; Fixr lists $900 to $1,500 for gas or propane and $500 to $1,000 for electric, at $75 to $130 per hour for 6 to 10 hours. Benchmark: BLS reports a May 2025 national median wage of $30.67 per hour for plumbers, pipefitters, and steamfitters; that is what an employee earns, not what a contractor bills.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| New or Larger Gas Line | $500 – $1,000This Old House, Fixr, Bob Vila | As Needed | This Old House lists it as a part of a tankless installation; ask whether the installed quote already includes it. Fixr says a new gas line adds up to $800; Bob Vila listed up to $1,000 in 2023. |
| Venting Work | $500 – $1,000This Old House | Common | Gas tankless units need their own vent; This Old House lists venting as a part of a tankless installation, so check whether the quote already includes it. |
| Electrical Upgrades | $300 – $800This Old House, Fixr, Bob Vila | As Needed | This Old House range, listed as a part of a tankless installation; electricians bill $65 to $85 per hour (Fixr; Bob Vila listed $50 to $100 in 2023). |
| Cold-Climate Venting and Insulation | Up to $400Fixr | As Needed | Fixr's figure for a nearby vent and pipe insulation where incoming water is cold. |
| Removing the Old Tank | $100 – $500+This Old House, Fixr | Common | This Old House lists water heater removal at $100 to $300; Fixr says removing the current system can cost upwards of $500 depending on the area. |
| Piping and Insulation | About $10 per footBob Vila | As Needed | Bob Vila (2023) figure for new piping and insulation. |
| Permit and Inspection | $50 – $200This Old House, Bob Vila | As Needed | This Old House range for a water heater installation; Bob Vila listed $50 to $100 in 2023. |
Calculator
Tankless Water Heater Installation Cost Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Fuel and system
A ZIP code scales the labor share of the estimate (about 40%) by the BLS wage ratio for the trade.
National planning estimate. Not a quote.
- Fuel and system: Whole-house unit (This Old House range)
- $2,100 – $4,000
- Location
- National
A ZIP code or state changes only the labor share of the estimate, using the BLS Occupational Employment and Wage Statistics (May 2025) wage ratio for the trade. Materials, equipment and permits stay at national figures. Planning estimates, not contractor quotes.
The first option is the guide's typical range; the fuel options use Fixr's rows from the table on this page.
This Old House builds its installed range from the unit, labor and, where needed, a gas line, electrical work and venting, so the add-ons may already be inside it: add them only when your quote lists them separately.
Electrical panel upgrades and wall repairs are not included.
Location
Personalize This Estimate by ZIP or State
A ZIP code or state changes only the labor share of this guide's range (about 40%), using BLS wage data for the trade. Materials, equipment and permits stay at national figures. Results are estimates, not contractor quotes.
National figures: typical $2,100 – $4,000, average $2,800.
Leave empty for national figures.
$2,800
National average $2,800 · no location applied
- Typical range
- $2,100 – $4,000
- Full project range
- $600 – $6,000
- Labor index (BLS wage ratio)
- 1.00×
- Materials, equipment, permits
- National (not adjusted)
$800 – $1,500
National labor band. Hourly rate cited in this guide: $75–$130/hr (national).
$1,000 – $2,000
This guide's national allowance (see its sources); not adjusted by location.
Permits and inspections
This guide's permit allowance: $50 – $200. Fees and rules are set by each city or county; this is not a local fee lookup, so ask the contractor who pulls the permit and what it costs.
Typical range in all 50 states and DC
Modeled, not published by a source: the national typical range with the labor share (about 40%) scaled by each state's BLS Occupational Employment and Wage Statistics (May 2025) mean wage for plumbers, pipefitters, and steamfitters, divided by the national mean of $34.70/hr. Materials, equipment and permits stay national.
| State | BLS mean wage | Labor index | Typical range | Average | Action |
|---|---|---|---|---|---|
| Alabama | $27.77/hr | 0.80× | $1,925 – $3,675 | $2,575 | |
| Alaska | $43.49/hr | 1.25× | $2,325 – $4,400 | $3,075 | |
| Arizona | $32.66/hr | 0.94× | $2,050 – $3,900 | $2,725 | |
| Arkansas | $24.35/hr | 0.70× | $1,850 – $3,525 | $2,475 | |
| California | $39.58/hr | 1.14× | $2,225 – $4,225 | $2,950 | |
| Colorado | $33.22/hr | 0.96× | $2,075 – $3,925 | $2,750 | |
| Connecticut | $36.25/hr | 1.04× | $2,150 – $4,075 | $2,850 | |
| Delaware | $32.75/hr | 0.94× | $2,050 – $3,900 | $2,725 | |
| District of Columbia | $43.85/hr | 1.26× | $2,325 – $4,425 | $3,100 | |
| Florida | $26.94/hr | 0.78× | $1,900 – $3,650 | $2,550 | |
| Georgia | $27.99/hr | 0.81× | $1,950 – $3,700 | $2,575 | |
| Hawaii | $39.81/hr | 1.15× | $2,225 – $4,225 | $2,975 | |
| Idaho | $28.10/hr | 0.81× | $1,950 – $3,700 | $2,575 | |
| Illinois | $44.91/hr | 1.29× | $2,350 – $4,475 | $3,125 | |
| Indiana | $36.37/hr | 1.05× | $2,150 – $4,075 | $2,850 | |
| Iowa | $33.67/hr | 0.97× | $2,075 – $3,950 | $2,775 | |
| Kansas | $34.33/hr | 0.99× | $2,100 – $3,975 | $2,800 | |
| Kentucky | $33.11/hr | 0.95× | $2,050 – $3,925 | $2,750 | |
| Louisiana | $30.11/hr | 0.87× | $2,000 – $3,800 | $2,650 | |
| Maine | $32.00/hr | 0.92× | $2,025 – $3,875 | $2,725 | |
| Maryland | $35.34/hr | 1.02× | $2,125 – $4,025 | $2,825 | |
| Massachusetts | $43.46/hr | 1.25× | $2,300 – $4,400 | $3,075 | |
| Michigan | $37.14/hr | 1.07× | $2,150 – $4,100 | $2,875 | |
| Minnesota | $41.68/hr | 1.20× | $2,275 – $4,325 | $3,025 | |
| Mississippi | $27.25/hr | 0.79× | $1,925 – $3,650 | $2,550 | |
| Missouri | $36.06/hr | 1.04× | $2,125 – $4,050 | $2,850 | |
| Montana | $37.59/hr | 1.08× | $2,175 – $4,125 | $2,900 | |
| Nebraska | $31.59/hr | 0.91× | $2,025 – $3,850 | $2,700 | |
| Nevada | $34.38/hr | 0.99× | $2,100 – $3,975 | $2,800 | |
| New Hampshire | $31.84/hr | 0.92× | $2,025 – $3,875 | $2,700 | |
| New Jersey | $44.51/hr | 1.28× | $2,350 – $4,450 | $3,125 | |
| New Mexico | $29.71/hr | 0.86× | $1,975 – $3,775 | $2,650 | |
| New York | $40.29/hr | 1.16× | $2,225 – $4,250 | $2,975 | |
| North Carolina | $27.27/hr | 0.79× | $1,925 – $3,650 | $2,550 | |
| North Dakota | $31.81/hr | 0.92× | $2,025 – $3,875 | $2,700 | |
| Ohio | $33.51/hr | 0.97× | $2,075 – $3,950 | $2,750 | |
| Oklahoma | $28.35/hr | 0.82× | $1,950 – $3,700 | $2,600 | |
| Oregon | $47.33/hr | 1.36× | $2,400 – $4,575 | $3,200 | |
| Pennsylvania | $37.05/hr | 1.07× | $2,150 – $4,100 | $2,875 | |
| Rhode Island | $39.23/hr | 1.13× | $2,200 – $4,200 | $2,950 | |
| South Carolina | $26.87/hr | 0.77× | $1,900 – $3,650 | $2,550 | |
| South Dakota | $26.70/hr | 0.77× | $1,900 – $3,625 | $2,550 | |
| Tennessee | $29.09/hr | 0.84× | $1,975 – $3,750 | $2,625 | |
| Texas | $29.22/hr | 0.84× | $1,975 – $3,750 | $2,625 | |
| Utah | $30.87/hr | 0.89× | $2,000 – $3,825 | $2,675 | |
| Vermont | $33.16/hr | 0.96× | $2,075 – $3,925 | $2,750 | |
| Virginia | $29.16/hr | 0.84× | $1,975 – $3,750 | $2,625 | |
| Washington | $42.69/hr | 1.23× | $2,300 – $4,375 | $3,050 | |
| West Virginia | $28.26/hr | 0.81× | $1,950 – $3,700 | $2,600 | |
| Wisconsin | $40.73/hr | 1.17× | $2,250 – $4,275 | $3,000 | |
| Wyoming | $29.76/hr | 0.86× | $1,975 – $3,775 | $2,650 |
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Gas Tankless Water Heater: Heat Exchanger, Venting and Service Valves
Part 1: Heat exchanger and burner
Heat water only while it flows through the unit, so there is no tank to keep hot.
Part 2: Venting
Gas tankless units need their own vent, often plastic pipe out a side wall on condensing models. The old tank’s vent often cannot be reused.
$500 – $1,000 · This Old House
Part 3: Gas supply
At full output these units burn far more gas than a tank heater, so the gas line or meter may need upsizing.
$500 – $1,000 · This Old House, Fixr, Bob Vila
Part 4: Isolation (service) valves
Let the plumber shut off and flush the heat exchanger to remove scale without disconnecting the unit.
Code and safety: Converting to a tankless heater usually needs a plumbing permit, and often gas or electrical work as well. Ask whether the quote includes venting, gas-line or circuit upgrades and the permit.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Plumbing fixture fitting and trim manufacturing (PPI) (opens in a new tab) | 398.136 | 417.588 | +4.9% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Payback
Energy Savings & Replacement Payback
Compare the operating cost of an older, less efficient unit with a more efficient replacement, and how long the difference takes to pay back.
Modeling assumption: your household’s daily use.
Modeling assumption: supply to tank setting, e.g. 50°F to 120°F.
Uniform Energy Factor from the EnergyGuide label (example value).
From the model you are quoted (example value).
Starts at the tankless water heater guide average.
Enter the repair you were quoted, if any.
EIA 2025 U.S. residential average: 17.23¢ per kWh.
EIA 2025 U.S. residential price, about $1.48 per therm.
From your utility or tax filing.
About $11 a month.
- Payback on the extra cost
- 22 years
- 10-year net result
- −$1,529
- Replacement
- $2,800
- Net out of pocket
- $2,800
- Repair instead
- Not entered
- Extra cost to recover
- $2,800
- 10-year utility savings
- $1,271
- 10-year return on the extra cost
- −55%
- CO₂ avoided a year (approx.)
- 1,001 lb
Defaults you can change: electricity 17.23¢ per kWh (EIA, U.S. residential average for 2025) and natural gas about $1.48 per therm (EIA's 2025 residential $15.34 per thousand cubic feet at 1,037 Btu per cubic foot; our conversion).
Energy a year = gallons a day × 8.34 lb × temperature rise × 365 ÷ UEF, in kWh (÷ 3,412 Btu) or therms (÷ 100,000 Btu). Use, temperature rise and UEF ratings are modeling assumptions you can change.
CO₂ uses 0.767 lb per kWh (EPA eGRID, 2023 U.S. average) and 11.67 lb per therm (EIA). Savings are not guaranteed; your bills, rates and use decide the result.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $2,800
$2,100 – $4,000
Average $2,800
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Tankless Water Heater Installation Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
This Old House reports $2,100 to $4,000 installed, about $2,800 on average. Fixr reports $2,500 to $4,500 (average $2,811), HomeGuide $1,400 to $5,600 and Angi $1,400 to $3,900; Bob Vila's $1,333 to $3,721 (average $2,527, updated 2023) credits Angi and HomeAdvisor. The spread comes from fuel type, unit size, and how much gas, venting and electrical work the house needs.
This Old House's $2,100 to $4,000 installed range is built from the unit ($1,000 to $2,000), labor ($800 to $1,500) and, where needed, a gas line ($500 to $1,000), electrical upgrades ($300 to $800) and venting ($500 to $1,000); ask whether a quote includes each rather than adding them on top. HomeGuide reports $2,100 to $5,600 for natural gas models including the unit, labor and needed modifications. Fixr's conversion section puts installing a gas unit, including the gas line, at about $1,700, and removing the old heater at upwards of $500.
When gas, venting and power are already in place, Fixr lists labor at $135 to $1,200 and a total of $600 to $6,000 depending on the replacement unit. Expect a lower bill than a first-time conversion because the vent and gas line can usually be reused.
Electric is cheaper to install: Fixr lists $1,000 to $3,000 installed for electric (labor $500 to $1,000) and $1,400 to $3,500 for gas or propane (labor $900 to $1,500). Gas is usually cheaper to run: Fixr's operating cost table shows about $250 a year for gas tankless against $600 for electric tankless.
It depends on fuel and use. Fixr's operating cost table shows gas tankless at about $250 a year against $275 for a gas tank, but electric tankless at about $600 against $450 for an electric tank; the same page also cites an average saving of about $116 a year without reconciling it with that table. On gas, the yearly saving is small next to the extra installation cost. Tankless units save floor space and supply hot water continuously, up to their rated flow: Fixr notes that units above 7 to 8 GPM are hard to find and that one unit may not keep up with several showers and appliances at once. Fixr says most tankless units last over twenty years.
Rinnai's residential units range from about 6.5 to 11 GPM. Size the unit for the fixtures that run at the same time and for your incoming water temperature; colder climates need more capacity. Fixr lists gas unit prices at $250 to $600 for 2 to 3 GPM, $500 to $800 for 5 to 6 GPM and $900 to $2,000 for 8 GPM or more, before installation.
Fixr estimates 6 to 10 hours, at $75 to $130 per hour for the plumber; This Old House says tankless systems need 4 to 6 hours for a complete setup, including gas lines, electrical work and venting. A conversion that adds a gas line, new venting or an electrical circuit takes longer than replacing an existing tankless unit.
Not at the moment. The Department of Energy's May 2024 water heater rule, which takes effect for units made from May 6, 2029, excludes gas-fired tankless models, and DOE's separate December 2024 rule for them was withdrawn as of May 20, 2025. The 2024 rule mainly changes storage tanks.
A complete quote names the unit and its GPM rating and lists the vent, gas line sizing, electrical work, condensate drain on condensing models, removal of the old tank and the permit. Red flags: a low price that assumes the existing 1/2-inch gas line or tank vent can be reused without checking, no mention of a permit, or no isolation valves for descaling. Rinnai's whole-house units draw up to 199,000 BTU and call for a 3/4-inch gas line.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Tankless water heater installation costs $2,100 to $4,000, about $2,800 on average (This Old House). | $2,100 – $4,000 | This Old House (opens in a new tab) | Source reviewed |
| Fixr reports $2,500 to $4,500 installed with a $2,811 average; electric $1,000 to $3,000 and gas or propane $1,400 to $3,500. | $2,500 – $4,500 | Fixr (opens in a new tab) | Source reviewed |
| This Old House lists venting ($500 to $1,000), a gas line ($500 to $1,000) and electrical upgrades ($300 to $800) among the parts of a tankless installation. | $300 – $1,000 per item | This Old House (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 5 independent (6 pages)
- 1.
- 2.
- 3.
- 4.
- 5.
- 6.
Wage data and technical references
- 7.
- 8.
- 9.
- 10.
What changed
- Full range now spans Fixr's $600 to $6,000 for replacing a tankless unit, so the replacement row no longer falls outside it. The conversion answer no longer adds venting, gas line and electrical work on top of This Old House's installed price, which already lists them as parts of the job. The "worth it" answer now shows that electric tankless costs more to run than an electric tank (Fixr) and that output is limited by flow rate. Permit figure now This Old House's $50 to $200; Bob Vila figures dated 2023.
