PlumbingFull System Replacement
Water Heater Replacement Cost in 2026: What a New Hot Water Heater Costs Installed
Water heater replacement typically costs $882 to $1,826. Angi average: $1,348.
Cost snapshot
U.S. national figures ·
- Typical range
- $882 – $1,826
- Angi average
- $1,348
- Full range
- $500 – $4,600
Where the typical range comes from: Angi's published typical range and average for replacing a water heater; the full range is Fixr's lowest and highest installed costs ($500 to $4,600).
Replacing a water heater typically costs $882 to $1,826, about $1,348 on average, according to Angi. Other publishers put it higher: Fixr reports $900 to $3,000 for most installations (average about $1,400; overall $500 to $4,600), and This Old House $1,200 to $2,300 for a tank model installed. Bob Vila's $874 to $1,765 (2024) credits Angi and HomeAdvisor, so it is not a separate check. Because the independent publishers disagree by more than 20%, confidence is medium. Labor is a minority of the bill: This Old House puts tank labor at $300 to $800 and the unit at $600 to $1,000. Heat pump and tankless models cost more ($1,200 to $4,600 and $1,000 to $4,000 installed, per Fixr). A repair usually costs $150 to $750 (Fixr).

Overview
Water Heater Replacement Cost: Overview
Water heater replacement typically costs $882 to $1,826 installed, about $1,348 on average (Angi). Compare sizes, gas vs electric, labor, repairs and permits.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $882 – $1,826Angi average: $1,348 | Medium confidence; cited: Angi, Fixr, This Old House, Bob Vila |
| Equipment or materials | $600 – $1,000 | Cited: This Old House, The Home Depot |
| Labor | $300 – $800 | Cited: This Old House, Fixr |
By size
Cost by Size & Scope
Plumbing costs scale with tank capacity or flow rate, pipe run length, and how difficult the work area is to reach.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| 40-Gallon Tank | Two or three people (This Old House range; Fixr lists $550 – $2,300). Average shown is the calculated midpoint. | $600 – $1,200 | $900 | This Old House, Fixr |
| 50-Gallon Tank | Three or four people need 50 – 60 gal per This Old House; Fixr says 3 – 5 people and lists $700 – $2,500. Average shown is the calculated midpoint. | $700 – $1,800 | $1,250 | This Old House, Fixr |
| 75-Gallon Tank | Five or more people (This Old House range; Fixr lists $1,100 – $3,400). Average shown is the calculated midpoint. | $900 – $2,300 | $1,600 | This Old House, Fixr |
| 80-Gallon Tank | Five or more people (This Old House range; Fixr lists $1,200 – $3,600). Average shown is the calculated midpoint. | $1,000 – $3,000 | $2,000 | This Old House, Fixr |
By type
Cost by Equipment & Installation Method
| Type | What it involves | Typical cost |
|---|---|---|
| Electric TankNo venting required | Resistance heating elements; no flue or gas line. Fixr lists $500 to $3,500 installed and Angi $600 to $3,500. Home Depot listed 50-gallon Rheem electric tanks at $599 and $619 (unit only). | $500 – $3,500 installedFixr, Angi, The Home Depot |
| Natural Gas TankNeeds a gas supply and a vent | Gas burner with a flue. Fixr's installation guide and Angi both list $700 to $2,700 installed for any gas water heater; Fixr lists propane at $700 to $2,500. For a standard gas tank replacing an existing one, see our gas water heater guide: $1,000 to $2,700 (Fixr's gas water heater page). Home Depot listed a 50-gallon Rheem gas tank at $719 (unit only). | $700 – $2,700 installedFixr, Angi, The Home Depot |
| Power-Vent Gas TankNeeds an outlet and a wall vent | A blower pushes exhaust out through a side wall where there is no chimney. Power venting adds $300 to $1,000 (Fixr installation guide); Fixr's gas water heater guide puts a new power vent at about $1,100, and This Old House lists $300 to $600 plus $300 to $500 of electrical work. | Gas tank price + $300 – $1,000Fixr, This Old House |
| Heat Pump (Hybrid) TankENERGY STAR certified models available | Moves heat from the surrounding air into the water, so it uses less electricity than a standard electric tank. Fixr lists $1,200 to $4,600 installed and This Old House $2,500 to $3,500. Home Depot listed a 50-gallon Rheem hybrid at $1,699 (unit only). | $1,200 – $4,600 installedFixr, This Old House, The Home Depot |
| Tankless (On-Demand)No storage tank | Heats water as it flows; usually needs a larger gas line or electrical service and new venting. Fixr's installation guide lists $1,000 to $4,000; our tankless water heater guide uses This Old House's $2,100 to $4,000 (about $2,800 on average), which is the better figure for a whole-house gas unit. | $1,000 – $4,000 installedFixr, This Old House |
| Water Heater Repair (Instead of Replacing)Repair, not a new unit | Fixing a part on a working tank. Fixr reports $150 to $750 for most repairs, $450 on average: thermocouple $150 to $325, heating element $200 to $750, thermostat $100 to $250, gas control valve $150 to $300, anode rod $125 to $300. Fixr says a repair quote of $1,000 or more may favor a new heater. See the repair questions below. | $150 – $750 per repairFixr |
Breakdown
Parts vs. Labor Breakdown
What the equipment or materials cost compared with the installer's labor, and what each figure is based on.
Plumbers and Pipefitters
- Labor range
- $300 – $800
- Planning estimate of on-site hours
- 1 – 3 hrs
- BLS median employee wage
- $30.67/hr
- Equipment or materials: $600 – $1,000
- The new tank water heater. This Old House lists $600 to $1,000 for a tank unit. As a retail check, Home Depot listed a Rheem 50-gallon natural gas tank at $719 and 50-gallon electric tanks at $599 and $619 on 2026-10-09 (equipment only).
- Labor: $300 – $800
- Plumber labor for a tank swap: draining and disconnecting the old tank, setting the new one, connecting water and gas or power, and testing. This Old House lists $300 to $800 for tank labor; Fixr lists $200 to $650 for a gas tank replacement. Published hourly rates are $40 to $200 (This Old House) and $45 to $200 (Fixr). This Old House says a standard tank installation usually takes 1 to 3 hours, and Fixr 2 to 3 hours for a gas tank. Benchmark: BLS reports a May 2025 national median wage of $30.67 per hour for plumbers, pipefitters, and steamfitters; that is what an employee earns, not what a contractor bills.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| Thermal Expansion Tank | $40 – $150This Old House | As Needed | Required by some cities when the water supply has a backflow preventer (This Old House). |
| Earthquake Strapping | $100 – $300This Old House, Fixr | As Needed | Required in seismic areas; Fixr lists installed straps at $100 to $200. |
| Temperature & Pressure Relief Valve | $20 – $200This Old House | Common | This Old House range for the valve and its work. |
| Drain Pan or Drainage | $50 – $200This Old House | As Needed | Proper drainage where a leak could damage floors (This Old House). |
| Gas Venting or Chimney Liner | $300 – $700This Old House | As Needed | Basic gas venting $300 to $500; a new chimney liner $500 to $700 (This Old House). |
| Attic Installation | $200 – $1,000 extraThis Old House | As Needed | Harder access raises labor (This Old House). |
| First-Time Installation (No Existing Heater) | $400 – $1,800 extraFixr, This Old House | As Needed | Fixr's added cost to rough in utilities for a new installation instead of a replacement. Moving an existing heater is not priced separately: Fixr says it "will significantly increase labor costs", and This Old House lists water line changes at $200 to $600. |
| Switching Fuel (Electric to Gas) | $1,500 – $2,300This Old House, Fixr | Optional | New gas lines when converting from electric (This Old House). Fixr reports $3,500 or more to switch from electric or oil to gas. |
| Emergency or After-Hours Service | $200 – $500This Old House, Fixr | Optional | This Old House range; Fixr lists an emergency surcharge of $100 to $200 for repairs. |
Calculator
Water Heater Replacement Cost Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Tank size
2Heater type
A ZIP code scales the labor share of the estimate (about 35%) by the BLS wage ratio for the trade.
National planning estimate. Not a quote.
- Tank size: Not sure (standard 40- or 50-gallon tank)
- $882 – $1,826
- Heater type
- Standard gas or electric tank
- Location
- National
A ZIP code or state changes only the labor share of the estimate, using the BLS Occupational Employment and Wage Statistics (May 2025) wage ratio for the trade. Materials, equipment and permits stay at national figures. Planning estimates, not contractor quotes.
The 'not sure' option is this guide's typical range from the cost snapshot.
Size options use This Old House's by-size rows on this page.
With the size 'not sure', the heat pump option shows Fixr's $1,200 to $4,600 installed range. With a tank size selected, the size row is multiplied by the ratio of Fixr's heat pump midpoint ($2,900) to this guide's typical midpoint, about 2.1x: a calculation, not a published price.
No federal tax credits or utility rebates are deducted. The federal Section 25C credit ended for equipment placed in service after December 31, 2025; check current state and utility incentives.
Location
Personalize This Estimate by ZIP or State
A ZIP code or state changes only the labor share of this guide's range (about 35%), using BLS wage data for the trade. Materials, equipment and permits stay at national figures. Results are estimates, not contractor quotes.
National figures: typical $882 – $1,826, average $1,348.
Leave empty for national figures.
$1,348
National average $1,348 · no location applied
- Typical range
- $882 – $1,826
- Full project range
- $500 – $4,600
- Labor index (BLS wage ratio)
- 1.00×
- Materials, equipment, permits
- National (not adjusted)
$300 – $800
National labor band. Hourly rate cited in this guide: $40–$200/hr (national).
$600 – $1,000
This guide's national allowance (see its sources); not adjusted by location.
Permits and inspections
This guide's permit allowance: $50 – $200. Fees and rules are set by each city or county; this is not a local fee lookup, so ask the contractor who pulls the permit and what it costs.
Typical range in all 50 states and DC
Modeled, not published by a source: the national typical range with the labor share (about 35%) scaled by each state's BLS Occupational Employment and Wage Statistics (May 2025) mean wage for plumbers, pipefitters, and steamfitters, divided by the national mean of $34.70/hr. Materials, equipment and permits stay national.
| State | BLS mean wage | Labor index | Typical range | Average | Action |
|---|---|---|---|---|---|
| Alabama | $27.77/hr | 0.80× | $820 – $1,700 | $1,250 | |
| Alaska | $43.49/hr | 1.25× | $960 – $2,000 | $1,475 | |
| Arizona | $32.66/hr | 0.94× | $865 – $1,800 | $1,325 | |
| Arkansas | $24.35/hr | 0.70× | $790 – $1,625 | $1,200 | |
| California | $39.58/hr | 1.14× | $925 – $1,925 | $1,425 | |
| Colorado | $33.22/hr | 0.96× | $870 – $1,800 | $1,325 | |
| Connecticut | $36.25/hr | 1.04× | $895 – $1,850 | $1,375 | |
| Delaware | $32.75/hr | 0.94× | $865 – $1,800 | $1,325 | |
| District of Columbia | $43.85/hr | 1.26× | $965 – $2,000 | $1,475 | |
| Florida | $26.94/hr | 0.78× | $815 – $1,675 | $1,250 | |
| Georgia | $27.99/hr | 0.81× | $820 – $1,700 | $1,250 | |
| Hawaii | $39.81/hr | 1.15× | $925 – $1,925 | $1,425 | |
| Idaho | $28.10/hr | 0.81× | $825 – $1,700 | $1,250 | |
| Illinois | $44.91/hr | 1.29× | $975 – $2,025 | $1,475 | |
| Indiana | $36.37/hr | 1.05× | $895 – $1,850 | $1,375 | |
| Iowa | $33.67/hr | 0.97× | $875 – $1,800 | $1,325 | |
| Kansas | $34.33/hr | 0.99× | $880 – $1,825 | $1,350 | |
| Kentucky | $33.11/hr | 0.95× | $870 – $1,800 | $1,325 | |
| Louisiana | $30.11/hr | 0.87× | $840 – $1,750 | $1,275 | |
| Maine | $32.00/hr | 0.92× | $860 – $1,775 | $1,300 | |
| Maryland | $35.34/hr | 1.02× | $890 – $1,850 | $1,350 | |
| Massachusetts | $43.46/hr | 1.25× | $960 – $1,975 | $1,475 | |
| Michigan | $37.14/hr | 1.07× | $905 – $1,875 | $1,375 | |
| Minnesota | $41.68/hr | 1.20× | $945 – $1,950 | $1,450 | |
| Mississippi | $27.25/hr | 0.79× | $815 – $1,700 | $1,250 | |
| Missouri | $36.06/hr | 1.04× | $895 – $1,850 | $1,375 | |
| Montana | $37.59/hr | 1.08× | $910 – $1,875 | $1,375 | |
| Nebraska | $31.59/hr | 0.91× | $855 – $1,775 | $1,300 | |
| Nevada | $34.38/hr | 0.99× | $880 – $1,825 | $1,350 | |
| New Hampshire | $31.84/hr | 0.92× | $855 – $1,775 | $1,300 | |
| New Jersey | $44.51/hr | 1.28× | $970 – $2,000 | $1,475 | |
| New Mexico | $29.71/hr | 0.86× | $840 – $1,725 | $1,275 | |
| New York | $40.29/hr | 1.16× | $930 – $1,925 | $1,425 | |
| North Carolina | $27.27/hr | 0.79× | $815 – $1,700 | $1,250 | |
| North Dakota | $31.81/hr | 0.92× | $855 – $1,775 | $1,300 | |
| Ohio | $33.51/hr | 0.97× | $870 – $1,800 | $1,325 | |
| Oklahoma | $28.35/hr | 0.82× | $825 – $1,700 | $1,250 | |
| Oregon | $47.33/hr | 1.36× | $995 – $2,050 | $1,525 | |
| Pennsylvania | $37.05/hr | 1.07× | $905 – $1,875 | $1,375 | |
| Rhode Island | $39.23/hr | 1.13× | $920 – $1,900 | $1,400 | |
| South Carolina | $26.87/hr | 0.77× | $810 – $1,675 | $1,250 | |
| South Dakota | $26.70/hr | 0.77× | $810 – $1,675 | $1,250 | |
| Tennessee | $29.09/hr | 0.84× | $830 – $1,725 | $1,275 | |
| Texas | $29.22/hr | 0.84× | $835 – $1,725 | $1,275 | |
| Utah | $30.87/hr | 0.89× | $850 – $1,750 | $1,300 | |
| Vermont | $33.16/hr | 0.96× | $870 – $1,800 | $1,325 | |
| Virginia | $29.16/hr | 0.84× | $835 – $1,725 | $1,275 | |
| Washington | $42.69/hr | 1.23× | $955 – $1,975 | $1,450 | |
| West Virginia | $28.26/hr | 0.81× | $825 – $1,700 | $1,250 | |
| Wisconsin | $40.73/hr | 1.17× | $935 – $1,925 | $1,425 | |
| Wyoming | $29.76/hr | 0.86× | $840 – $1,725 | $1,275 |
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Tank Water Heater Anatomy: Dip Tube, Anode Rod, Burner and Relief Valve
Part 1: Dip tube
Carries incoming cold water to the bottom of the tank, so it is heated before it rises to the hot outlet.
Part 2: Sacrificial anode rod
A metal rod that corrodes instead of the steel tank. Replacing it in time can extend the tank’s life.
Part 3: Gas burner and flue baffle
The burner heats the tank from below; the baffle inside the central flue slows the exhaust so more of its heat goes into the water.
Part 4: Temperature and pressure relief valve
Opens if the water gets too hot or the pressure too high. Its discharge pipe should run down toward the floor or a drain.
$20 – $200 · This Old House
Part 5: Thermal expansion tank
Mounts on the cold supply line and absorbs the extra volume of heated water when a check valve or pressure regulator stops it from flowing back to the main.
$40 – $150 · This Old House
Code and safety: Most jurisdictions require a permit to replace a water heater. Ask the installer to confirm the relief-valve discharge, the venting on gas models and whether your local code calls for an expansion tank.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Plumbing fixture fitting and trim manufacturing (PPI) (opens in a new tab) | 398.136 | 417.588 | +4.9% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Payback
Energy Savings & Replacement Payback
Compare the operating cost of an older, less efficient unit with a more efficient replacement, and how long the difference takes to pay back.
Modeling assumption: your household’s daily use.
Modeling assumption: supply to tank setting, e.g. 50°F to 120°F.
Uniform Energy Factor from the EnergyGuide label (example value).
From the model you are quoted (example value).
Starts at the midpoint of Fixr's $1,200 to $4,600 heat pump water heater range (water heater replacement guide).
Enter the repair you were quoted, if any.
EIA 2025 U.S. residential average: 17.23¢ per kWh.
EIA 2025 U.S. residential price, about $1.48 per therm.
From your utility or tax filing.
About $45 a month.
- Payback on the extra cost
- 5.3 years
- 10-year net result
- +$2,552
- Replacement
- $2,900
- Net out of pocket
- $2,900
- Repair instead
- Not entered
- Extra cost to recover
- $2,900
- 10-year utility savings
- $5,452
- 10-year return on the extra cost
- +88%
- CO₂ avoided a year (approx.)
- 2,428 lb
Defaults you can change: electricity 17.23¢ per kWh (EIA, U.S. residential average for 2025) and natural gas about $1.48 per therm (EIA's 2025 residential $15.34 per thousand cubic feet at 1,037 Btu per cubic foot; our conversion).
Energy a year = gallons a day × 8.34 lb × temperature rise × 365 ÷ UEF, in kWh (÷ 3,412 Btu) or therms (÷ 100,000 Btu). Use, temperature rise and UEF ratings are modeling assumptions you can change.
CO₂ uses 0.767 lb per kWh (EPA eGRID, 2023 U.S. average) and 11.67 lb per therm (EIA). Savings are not guaranteed; your bills, rates and use decide the result.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $1,348
$882 – $1,826
Average $1,348
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Water Heater Replacement Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
Angi reports a typical range of $882 to $1,826 to replace a water heater, about $1,348 on average, including the new unit and installation. Other publishers are higher: Fixr reports $900 to $3,000 for most installations (average about $1,400), and This Old House $1,200 to $2,300 for a tank model installed. Bob Vila's $874 to $1,765 (updated 2024) credits Angi and HomeAdvisor. Heat pump and tankless models, attic installs and fuel conversions cost more.
This Old House lists $600 to $1,000 for a tank unit, and about $850 for an electric model and $800 for a gas model before venting. As retail examples, Home Depot listed a Rheem 50-gallon gas tank at $719, 50-gallon electric tanks at $599 and $619, and a 50-gallon hybrid heat pump tank at $1,699 on 2026-10-09. Installation, connections and haul-away are extra.
Installed, Fixr lists electric tanks at $500 to $3,500, natural gas tanks at $700 to $2,700, propane at $700 to $2,500, heat pump (hybrid) models at $1,200 to $4,600 and tankless units at $1,000 to $4,000. Angi lists gas at $700 to $2,700 and electric at $600 to $3,500. Power venting adds $300 to $1,000 (Fixr installation guide); Fixr's gas water heater guide puts a new power vent at about $1,100. Our gas water heater guide ($1,000 to $2,700 for a standard gas tank, Fixr) and tankless guide ($2,100 to $4,000, This Old House) break those down further.
This Old House lists $600 to $1,200 for a 40-gallon tank and $700 to $1,800 for a 50-gallon tank, installed. Fixr gives wider ranges of $550 to $2,300 (40 gallons) and $700 to $2,500 (50 gallons), and Angi lists $800 to $2,500 for a 50-gallon unit. Larger tanks cost more: $900 to $2,300 for 75 gallons and $1,000 to $3,000 for 80 gallons (This Old House). This Old House's by-size figures are lower than its own $1,200 to $2,300 installed range for tank models, and the page does not reconcile them; the averages in our size table are calculated midpoints, not published averages.
This Old House puts labor for a tank replacement at $300 to $800, and Fixr lists $200 to $650 for a gas tank (about 20% to 25% of the total). Tankless labor is higher: $800 to $1,500 (This Old House). Plumbers bill $40 to $200 per hour. Our water heater installation labor cost guide covers labor-only quotes, including installing a heater you bought yourself.
Fixr lists $500 to $3,500 installed for an electric water heater and Angi $600 to $3,500. In the Department of Energy's 2024 rule, a baseline electric storage unit of 20 to 55 gallons averaged $902 installed in 2022 dollars, against $1,432 for a baseline gas unit. Switching from electric to gas adds new gas lines: $1,500 to $2,300 per This Old House.
A standard quote usually covers the new unit, labor, water and fuel connections, and often haul-away of the old tank. Items that are often priced separately: permit and inspection ($50 to $200), removal and disposal ($100 to $300), an expansion tank ($40 to $150), earthquake strapping ($100 to $300), drainage ($50 to $200), gas venting ($300 to $500) and attic access ($200 to $1,000), all per This Old House. Ask each installer to list these lines so quotes can be compared like for like.
Fixr reports $150 to $750 for most water heater repairs, $450 on average, with a low of $75 and a high of $2,000; electric units run $100 to $650 and gas or propane units $150 to $750. By part, with labor: pilot light $75 to $150, thermostat $100 to $250, dip tube $100 to $250, pressure relief valve $100 to $250, gas control valve $150 to $300, anode rod $125 to $300, thermocouple $150 to $325 and heating element $200 to $750. By problem: a leak $50 to $600, a backdraft $100 to $500, losing heat $100 to $750 and rust $200 to $2,000. Expect a call-out fee of around $50 and an emergency surcharge of $100 to $200 outside business hours (Fixr).
Fixr says a repair quote of $1,000 or more may favor a new heater, and that repairs are usually worthwhile on younger units; its gas water heater guide puts it as "at least half its lifespan remaining". A leaking tank body cannot be repaired; Fixr prices a tank replacement at $600 to $2,000. For age, Fixr says most water heaters last about 8 to 10 years on its repair page and 8 to 12 years for tank models on its installation page, while the Department of Energy assumes about 14.5 years for gas storage models and about 15 years for electric ones. Check the manufacturer warranty first: Fixr notes it usually covers the tank and replacement parts.
This Old House suggests considering a replacement when the unit reaches 10 years old, produces rusty water or no longer meets your hot water demand. Fixr adds leaks, unusual noises, high utility bills, and strange odors or discolored water, and says tank models typically last 8 to 12 years. In its 2024 rule the Department of Energy assumes an average life of about 14.5 years for gas storage water heaters and about 15 years for electric ones, so lifespans vary widely with water quality and maintenance.
This Old House says a standard tank installation usually takes 1 to 3 hours, and Fixr says 2 to 3 hours on average for a gas tank. Tankless systems take longer: 4 to 6 hours per This Old House, and Fixr's tankless guide estimates 6 to 10 hours. Attic installs, new venting, a fuel conversion or a first-time installation add time.
Usually not. Fixr says that "in most cases, homeowner's insurance will not cover water heater replacement." Check the manufacturer warranty instead: Fixr notes that it usually covers the tank and replacement parts, so a covered failure can cost less to repair. Ask your insurer separately about water damage caused by a leak.
Usually yes. Fixr says most local building departments require a permit to replace a water heater, and This Old House says most jurisdictions require one, especially for fuel changes or venting changes. This Old House lists permits and inspections at $50 to $200; Fixr reports $25 to $1,500, with the high end for new gas lines, electrical work or major plumbing changes. Ask who pulls the permit and whether it is in the quote.
Before it fails, if you can. This Old House notes that replacing a unit before it breaks avoids emergency rates, which it lists at $200 to $500 extra for after-hours service. Fixr says late spring and early summer are typically slower for plumbers, which may mean lower labor costs.
The Department of Energy's May 2024 rule sets new efficiency standards for water heaters manufactured or imported on or after May 6, 2029; it does not require you to replace a working heater. DOE says the levels for larger electric storage water heaters are met with heat pump technology, while electric resistance models stay available in its small electric storage class. For gas storage tanks DOE adopted its efficiency level 2 and states that the rule does not require a condensing level. Gas tankless models are not covered by this rule, and DOE's separate December 2024 tankless rule was withdrawn as of May 20, 2025.
DOE's 2024 rule estimates average installed costs in 2022 dollars: about $1,432 for a baseline gas-fired storage water heater (20 to 55 gallons), and $1,470 to $2,241 at the higher efficiency levels in its cost table; about $902 for a baseline electric storage unit of that size and $1,855 to $1,995 at higher efficiency levels. These are national averages from DOE's analysis, so current prices are higher after inflation, and they do not include electrical upgrades when switching fuel types.
Yes. This Old House reports that Pacific Northwest prices can run up to 45% above its $1,950 national average and Gulf Coast prices 10% to 20% above, while the Mid-Atlantic and Midwest run about 5% to 10% below and South Florida about 20% below. Local codes also add items such as seismic strapping ($100 to $300) or an expansion tank ($40 to $150). Our calculator adjusts only the labor share of the estimate for your ZIP code, using BLS plumber wage data.
Watch for a single lump-sum price with no model number, tank size or fuel type; no mention of a permit where your city requires one; vague wording about haul-away or code items such as an expansion tank or strapping; and pressure to upgrade to tankless without a written gas line, venting and electrical scope. Fixr notes that the permit alone can range from $25 to $1,500, so ask who pulls it and whether it is in the price.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Water heater replacement typically costs $882 to $1,826, about $1,348 on average (Angi); Fixr reports $900 to $3,000 with an average of about $1,400. | $882 – $1,826 | Angi (HomeAdvisor) (opens in a new tab)Fixr (opens in a new tab) | Source reviewed |
| Electric water heaters cost $500 to $3,500 installed (Fixr); Angi lists $600 to $3,500. | $500 – $3,500 | Fixr (opens in a new tab)Angi (HomeAdvisor) (opens in a new tab) | Source reviewed |
| Natural gas water heaters cost $700 to $2,700 installed (Fixr and Angi). | $700 – $2,700 | Fixr (opens in a new tab)Angi (HomeAdvisor) (opens in a new tab) | Source reviewed |
| This Old House lists tank replacement labor at $300 to $800 and a tank unit at $600 to $1,000. | $300 – $800 labor | This Old House (opens in a new tab) | Source reviewed |
| Fixr reports an average water heater repair of $450 (typically $150 to $750) and a thermocouple replacement of $150 to $325. | $150 – $750 | Fixr (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 4 independent (7 pages)
- 1.
- 2.
- 3.
- 4.Fixr: Water Heater Repair Cost (opens in a new tab)Read Nov 9, 2026
- 5.
- 6.
- 7.
Wage data and technical references
- 8.
- 9.
- 10.
- 11.
- 12.
What changed
- Headline changed from our $900 to $2,000 planning range to Angi's published $882 to $1,826 (average $1,348), with Fixr, This Old House and Bob Vila shown for comparison. Added a water heater repair section, signs of failure, job duration, insurance, permit and timing answers from Fixr and This Old House, and the 2029 federal efficiency rule as published by DOE. Corrected the DOE "condensing" wording, the first-time installation line and the size-table averages (calculated midpoints).
