HVACComponent Replacement
Furnace Repair Cost in 2026: Estimates by Part, Water Leaks & Heat Exchanger
Furnace repair typically costs $150 to $600. Midpoint of Fixr's $350 to $400 national average: $375.
Cost snapshot
U.S. national figures ·
- Typical range
- $150 – $600
- Midpoint of Fixr's $350 to $400 national average
- $375
- Full range
- $66 – $2,673
Where the typical range comes from: Fixr's 2026 HVAC repair guide (October 2026) for a typical furnace repair; the outer ends are the $66 low and $2,673 high on Fixr's furnace repair page.
A furnace repair typically costs $150 to $600, with a national average of $350 to $400, according to Fixr's 2026 HVAC repair guide; that covers the service call, the part and the labor. Angi reports a similar $318 average (typical $133 to $505), and Fixr's furnace repair page reports $485 ($349 to $650). Small parts cost the least (Fixr: flame sensor $68 to $127, ignitor $96 to $178, each with the service call). A cracked heat exchanger is the most expensive repair: $500 to $1,500 according to Angi and $1,346 to $2,673 according to Fixr. When a repair approaches half the price of a new furnace ($2,800 to $7,500 per Fixr), compare it with a replacement quote.

Overview
Furnace Repair Cost: Overview
Furnace repair typically costs $150 to $600, about $350 to $400 on average (Fixr). See estimates by part, water leaks, heat exchangers and repair vs replace.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $150 – $600Midpoint of Fixr's $350 to $400 national average: $375 | Medium confidence; cited: Fixr, Angi, Forbes Home |
| Equipment or materials | $45 – $320 | Cited: Fixr, Forbes Home |
| Labor | $95 – $300 | Cited: Fixr, Angi |
By size
Cost by Capacity & Scope
HVAC costs scale with system capacity (tonnage or motor size), the size of the home being served, and the scope of the work.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| Small part or minor fix | Limit switch, flame sensor, ignitor or thermostat, with the service call (Fixr; average shown is the midpoint) | $66 – $178 | $122 | Fixr |
| Standard part replacement | Igniter, flame sensor or pressure switch (Fixr 2026 guide; average shown is the midpoint) | $100 – $400 | $250 | Fixr |
| Control board replacement | Control circuit board with the service call (Fixr; average shown is the midpoint). Draft inducer motors are listed under repair types. | $390 – $725 | $558 | Fixr |
| Heat exchanger replacement | Cracked heat exchanger, Angi range; midpoint shown (Fixr publishes $1,346 to $2,673, and $1,000 to $3,500+ in its 2026 guide) | $500 – $1,500 | $1,000 | Angi, Fixr |
By type
Cost by Repair Type
| Type | What it involves | Typical cost |
|---|---|---|
| Flame Sensor Cleaning or ReplacementSafety lockout | A dirty or failed flame sensor shuts the burners off a few seconds after they light. Often cleaned rather than replaced. | $68 – $127 (Fixr) · $100 – $300 (Fixr 2026 guide) |
| Hot Surface IgnitorNo heat, burners do not light | The ignitor glows to light the burners; when it cracks, the furnace will not fire. | $96 – $178 (Fixr) · $150 – $250 (Forbes) |
| Limit or Pressure SwitchShort cycling or lockout | Safety switches that shut the furnace down when it overheats or when the venting does not draw properly. | Limit $66 – $122 (Fixr) · pressure $200 – $400 (Fixr 2026) |
| Control Circuit BoardElectronic failure | The board that sequences ignition, safety checks and the blower. | $390 – $725 (Fixr) · up to $600 (Forbes) |
| Draft Inducer MotorNoise or failed start | The small fan that clears exhaust before the burners light. | $200 – $500 repair · up to $1,500 replaced (Forbes) |
| Blower MotorNo airflow | The main fan that pushes warm air through the ducts. See the blower motor guide for PSC and ECM prices. | $562 – $1,045 (Fixr) |
| Condensate Drain or Pump (Furnace Leaking Water)Water around the furnace | High-efficiency furnaces make water that drains through a line or a small pump; a clog or failed pump makes the furnace leak. Fixr prices these items for AC and heat pump systems, which use the same parts. | Drain $75 – $250 · pump $100 – $450 (Fixr) |
| Heat Exchanger Repair or ReplacementMost expensive repair | A cracked heat exchanger can leak combustion gases and is a common reason to replace an older furnace instead. | Repair $100 – $200 · replace $500 – $1,500 (Angi) to $1,346 – $2,673 (Fixr)Forbes Home |
| Gas ValveGas supply | Controls gas flow to the burners. Gas work should only be done by a licensed technician. | Not published by our sources; ask for an itemized quoteForbes Home |
Breakdown
Parts vs. Labor Breakdown
What the equipment or materials cost compared with the installer's labor, and what each figure is based on.
HVAC Mechanics and Installers
- Labor range
- $95 – $300
- Planning estimate of on-site hours
- 1 – 3 hrs
- BLS median employee wage
- $29.33/hr
- Equipment or materials: $45 – $320
- The replacement part: ignitor, flame sensor, limit or pressure switch, control board, inducer motor or gas valve. Our sources publish installed prices (part plus labor), from $66 for a limit switch to $725 for a control board (Fixr), not part-only prices, so this split is a planning estimate. A heat exchanger is priced separately below.
- Labor: $95 – $300
- Diagnosis, part swap and safety testing. Fixr's 2026 HVAC repair guide lists $75 to $150 per hour, its furnace page $87 to $162 per hour depending on location, and Angi $50 to $150 per hour. Benchmark: BLS reports a May 2025 national median wage of $29.33 per hour for HVAC mechanics and installers; a contractor bills more because the rate also covers insurance, vehicles, equipment, overhead and margin.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| Diagnostic / Service Call Fee | $75 – $200Fixr | Required | Fixr's 2026 HVAC repair guide. Fixr says the fee is often applied to the repair if you hire the same company, and diagnosis usually takes 30 to 60 minutes. |
| After-Hours or Emergency Service | +$100 – $300Fixr | Optional | Fixr: 50% to 100% above standard rates, or an added $100 to $300. |
| Thermostat Replacement | $85 – $300Fixr | As Needed | Fixr thermostat guide; smart or Wi-Fi models $185 to $600. A failed thermostat can look like a furnace failure. |
| Condensate Drain Pan | $200 – $800This Old House, Fixr | As Needed | When water leaks from a cracked pan under the AC coil that sits on the furnace (This Old House $200 to $800; Fixr $200 to $600). |
| Annual Furnace Tune-Up | $70 – $300Fixr | Recommended | Fixr furnace guide. Maintenance is a separate service from repair. |
Calculator
Furnace Repair Cost Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Repair type
2Timing
A ZIP code scales the labor share of the estimate (about 48%) by the BLS wage ratio for the trade.
National planning estimate. Not a quote.
- Repair type: Not sure (typical repair)
- $150 – $600
- Timing
- Business-hours service call
- Location
- National
A ZIP code or state changes only the labor share of the estimate, using the BLS Occupational Employment and Wage Statistics (May 2025) wage ratio for the trade. Materials, equipment and permits stay at national figures. Planning estimates, not contractor quotes.
The 'not sure' option is this guide's typical range from the cost snapshot.
Repair-type options use the rows of this page's repair table.
Fixr says after-hours work runs 50% to 100% above standard rates or adds $100 to $300; the calculator adds $100 to $300.
Estimates include the service call and diagnosis. Ask whether the diagnostic fee ($75 to $200, Fixr) is credited toward the repair.
Location
Personalize This Estimate by ZIP or State
A ZIP code or state changes only the labor share of this guide's range (about 48%), using BLS wage data for the trade. Materials, equipment and permits stay at national figures. Results are estimates, not contractor quotes.
National figures: typical $150 – $600, average $375.
Leave empty for national figures.
$375
National average $375 · no location applied
- Typical range
- $150 – $600
- Full project range
- $66 – $2,673
- Labor index (BLS wage ratio)
- 1.00×
- Materials, equipment, permits
- National (not adjusted)
$95 – $300
National labor band. Hourly rate cited in this guide: $75–$150/hr (national).
$45 – $320
This guide's national allowance (see its sources); not adjusted by location.
Permits and inspections
This guide does not price a permit. Rules are set by each city or county; ask the contractor whether one is needed and who pulls it.
Typical range in all 50 states and DC
Modeled, not published by a source: the national typical range with the labor share (about 48%) scaled by each state's BLS Occupational Employment and Wage Statistics (May 2025) mean wage for heating, air conditioning, and refrigeration mechanics and installers, divided by the national mean of $31.14/hr. Materials, equipment and permits stay national.
| State | BLS mean wage | Labor index | Typical range | Average | Action |
|---|---|---|---|---|---|
| Alabama | $24.67/hr | 0.79× | $135 – $540 | $340 | |
| Alaska | $38.53/hr | 1.24× | $165 – $670 | $420 | |
| Arizona | $29.28/hr | 0.94× | $145 – $585 | $365 | |
| Arkansas | $24.59/hr | 0.79× | $135 – $540 | $335 | |
| California | $36.24/hr | 1.16× | $160 – $645 | $405 | |
| Colorado | $34.29/hr | 1.10× | $155 – $630 | $395 | |
| Connecticut | $35.38/hr | 1.14× | $160 – $640 | $400 | |
| Delaware | $31.80/hr | 1.02× | $150 – $605 | $380 | |
| District of Columbia | $40.83/hr | 1.31× | $170 – $690 | $430 | |
| Florida | $27.55/hr | 0.89× | $140 – $565 | $355 | |
| Georgia | $27.44/hr | 0.88× | $140 – $565 | $355 | |
| Hawaii | $32.24/hr | 1.03× | $155 – $610 | $380 | |
| Idaho | $28.85/hr | 0.93× | $145 – $580 | $360 | |
| Illinois | $37.29/hr | 1.20× | $165 – $655 | $410 | |
| Indiana | $31.30/hr | 1.00× | $150 – $600 | $375 | |
| Iowa | $30.35/hr | 0.97× | $150 – $595 | $370 | |
| Kansas | $29.55/hr | 0.95× | $145 – $585 | $365 | |
| Kentucky | $28.30/hr | 0.91× | $145 – $575 | $360 | |
| Louisiana | $27.35/hr | 0.88× | $140 – $565 | $355 | |
| Maine | $31.39/hr | 1.01× | $150 – $600 | $375 | |
| Maryland | $35.49/hr | 1.14× | $160 – $640 | $400 | |
| Massachusetts | $37.38/hr | 1.20× | $165 – $660 | $410 | |
| Michigan | $31.01/hr | 1.00× | $150 – $600 | $375 | |
| Minnesota | $35.57/hr | 1.14× | $160 – $640 | $400 | |
| Mississippi | $25.49/hr | 0.82× | $135 – $550 | $340 | |
| Missouri | $30.01/hr | 0.96× | $145 – $590 | $370 | |
| Montana | $29.94/hr | 0.96× | $145 – $590 | $370 | |
| Nebraska | $29.35/hr | 0.94× | $145 – $585 | $365 | |
| Nevada | $30.46/hr | 0.98× | $150 – $595 | $370 | |
| New Hampshire | $34.37/hr | 1.10× | $155 – $630 | $395 | |
| New Jersey | $37.30/hr | 1.20× | $165 – $655 | $410 | |
| New Mexico | $26.60/hr | 0.85× | $140 – $560 | $350 | |
| New York | $35.94/hr | 1.15× | $160 – $645 | $405 | |
| North Carolina | $27.60/hr | 0.89× | $140 – $565 | $355 | |
| North Dakota | $33.66/hr | 1.08× | $155 – $625 | $390 | |
| Ohio | $31.73/hr | 1.02× | $150 – $605 | $380 | |
| Oklahoma | $27.71/hr | 0.89× | $140 – $570 | $355 | |
| Oregon | $32.90/hr | 1.06× | $155 – $615 | $385 | |
| Pennsylvania | $31.19/hr | 1.00× | $150 – $600 | $375 | |
| Rhode Island | $33.55/hr | 1.08× | $155 – $620 | $390 | |
| South Carolina | $27.14/hr | 0.87× | $140 – $565 | $350 | |
| South Dakota | $29.37/hr | 0.94× | $145 – $585 | $365 | |
| Tennessee | $27.79/hr | 0.89× | $140 – $570 | $355 | |
| Texas | $28.43/hr | 0.91× | $145 – $575 | $360 | |
| Utah | $28.85/hr | 0.93× | $145 – $580 | $360 | |
| Vermont | $32.24/hr | 1.03× | $155 – $610 | $380 | |
| Virginia | $29.42/hr | 0.94× | $145 – $585 | $365 | |
| Washington | $37.91/hr | 1.22× | $165 – $665 | $415 | |
| West Virginia | $24.85/hr | 0.80× | $135 – $540 | $340 | |
| Wisconsin | $32.41/hr | 1.04× | $155 – $610 | $380 | |
| Wyoming | $26.81/hr | 0.86× | $140 – $560 | $350 |
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Inside a Condensing Gas Furnace: Burners, Inducer, Controls and Blower
Part 1: Hot-surface igniter
Glows hot enough to light the burners when the furnace starts.
$96 – $178 (Fixr) · $150 – $250 (Forbes)
Part 2: Flame sensor
Confirms the burners are lit; if it is dirty, the furnace shuts the gas off a few seconds after lighting.
$68 – $127 (Fixr) · $100 – $300 (Fixr 2026 guide)
Part 3: Inducer fan
Pulls combustion gases through the heat exchanger and out the vent pipe; a pressure switch must see it running before the burners light.
$200 – $500 repair · up to $1,500 replaced (Forbes)
Part 4: Control board
Runs the start-up sequence, the gas valve and the blower, and stores the fault codes a technician reads first.
$390 – $725 (Fixr) · up to $600 (Forbes)
Part 5: Circulating blower
Moves house air across the heat exchanger and through the ducts.
$562 – $1,045 (Fixr)
Part 6: Heat exchanger
Keeps the flame and exhaust separate from the air you breathe. A cracked heat exchanger can leak carbon monoxide.
Repair $100 – $200 · replace $500 – $1,500 (Angi) to $1,346 – $2,673 (Fixr) · Forbes Home
Code and safety: Gas valve, burner and heat exchanger work should be done by a licensed HVAC technician. If you smell gas or a carbon monoxide alarm sounds, leave the house and call the gas utility from outside.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Air-conditioning, refrigeration, and forced air heating equipment manufacturing (PPI) (opens in a new tab) | 312.596 | 324.82 | +3.9% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $375
$150 – $600
Average $375
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Furnace Repair Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
Most furnace repairs cost $150 to $600, with a national average of $350 to $400 (Fixr's 2026 HVAC repair guide). Other publishers are close: Angi reports a $318 average (typical $133 to $505), and Fixr's furnace repair page $485 ($349 to $650). Small parts such as a flame sensor or ignitor cost the least; a heat exchanger costs the most.
"Heater repair" can mean two different appliances with different prices. A furnace (or heat pump) heats the air in your rooms; a water heater heats the water for taps and showers. Furnace repairs typically cost $150 to $600 (Fixr's 2026 HVAC repair guide), and heat pump repairs average about $400 ($150 to $650, Fixr). Water heater repairs are priced separately: Fixr reports $150 to $750, about $450 on average, with a thermocouple at $150 to $325 and a heating element at $200 to $750. For a water heater that needs replacing, see our water heater replacement cost guide in the plumbing section.
A useful furnace repair estimate lists the diagnostic or service-call fee ($75 to $200 per Fixr), the part, the labor hours and rate ($75 to $150 per hour in Fixr's 2026 guide), any after-hours surcharge, and the warranty on parts and labor. Fixr says the diagnostic fee is often applied to the repair if you hire the same company, so ask before you approve the work, and get the failed part named in writing so you can compare it with the part prices in this guide.
A furnace that leaks water is usually a high-efficiency model with a clogged condensate drain or a failed condensate pump, or the AC coil and drain pan above it are leaking. Fixr prices a clogged condensate line at $75 to $250 and drain line cleaning at $75 to $300, a condensate pump at $100 to $450 (up to $500 on its AC page), and a drain pan at $200 to $600; This Old House lists drain pans at $200 to $800. These figures are published for AC and heat pump systems, which use the same parts. If the indoor coil itself is leaking, see the evaporator coil guide ($600 to $2,000).
Published prices disagree. Angi lists $500 to $1,500 to replace a heat exchanger and $100 to $200 to repair one; Forbes lists up to $1,500; Fixr's furnace repair page lists $1,346 to $2,673 including the service call, and its 2026 HVAC repair guide $1,000 to $3,500 or more. None of them publishes labor separately, so ask whether a quote is for the part and labor, or labor only because the part is under warranty. Fixr notes that this cost often leads owners to replace the furnace instead.
Fixr suggests repairs make sense when the furnace has five or more years of life left; furnaces typically last 15 to 20 years (oil up to 25, electric 20 to 30). Its 2026 HVAC guide also cites the "$5,000 rule" (repair cost times age in years) and replacing when a repair exceeds 50% of a new system. This Old House suggests considering replacement after about 15 years if repairs are frequent, and lists a cracked heat exchanger among the warning signs. A new furnace costs $2,800 to $7,500 installed (Fixr, $4,800 average).
Fixr lists an ignitor at $96 to $178 and a flame sensor at $68 to $127, each including the service call. Forbes lists $150 to $250 for an ignitor, and Fixr's 2026 HVAC guide $150 to $400 for igniters and $100 to $300 for flame sensors. A flame sensor can often be cleaned instead of replaced.
Fixr lists water leaking around the furnace, any smell of fuel or burning, a carbon monoxide alarm, squealing, whistling, groaning or clunking noises, a yellow instead of blue pilot flame, and rising utility bills from a furnace running inefficiently. A gas smell or a carbon monoxide alarm needs immediate attention: leave the house and call the gas utility or emergency services first.
Sometimes. Fixr notes that a furnace under ten years old may still be under warranty, and advises checking the warranty before any do-it-yourself fix. Manufacturer warranties usually cover parts rather than labor (This Old House says so for blower motors), so a covered repair can still cost the service call and labor. Ask the contractor to check the model's warranty status before quoting.
Before the heating season. Fixr recommends scheduling furnace maintenance before winter and notes that some companies raise service fees in winter to keep up with demand; after-hours and emergency calls cost 50% to 100% more, or an added $100 to $300 (Fixr 2026). This Old House also says contractors often charge higher rates in the winter months.
Fixr's 2026 HVAC repair guide reports $150 to $650 for most HVAC repairs, a $350 national average and a full range of $100 to $3,000. By system, it lists furnace repairs at $150 to $600, AC repairs at about $750 ($350 to $1,800) and heat pump repairs at a $410 average. This Old House reports most AC repairs at $150 to $650. Use the guide for the specific part once you know what failed.
Included: the service call, diagnosis, one replacement part, labor and a safety check. Not included: after-hours surcharges ($100 to $300 extra per Fixr), a new thermostat, duct repairs, permits where a city requires them, and a whole new furnace. A heat exchanger replacement is shown separately because it costs several times more than a typical repair.
Most of the difference is labor. Fixr lists furnace technicians at $87 to $162 per hour depending on location, and demand spikes in cold snaps can add after-hours charges. Enter your ZIP code above to adjust the labor share of this estimate with BLS wage data for your area.
Be cautious when a quote does not name the failed part or separate parts from labor, when a cracked heat exchanger is diagnosed without showing you the evidence, when you are pressed to replace the furnace on the spot, or when the price is far above the published ranges in this guide. This Old House recommends a second opinion before replacing a furnace.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Angi reports a $318 average furnace repair, with a typical range of $133 to $505. | $133 – $505 | Angi (HomeAdvisor) (opens in a new tab) | Source reviewed |
| Fixr reports a $485 national average furnace repair, with an average range of $349 to $650. | $349 – $650 | Fixr (opens in a new tab) | Source reviewed |
| Fixr's 2026 HVAC repair guide puts furnace repairs at $150 to $600, with a $350 to $400 national average, and a diagnostic fee at $75 to $200. This is the guide's typical range. | $150 – $600 | Fixr (opens in a new tab) | Source reviewed |
| Heat exchanger replacement: $500 to $1,500 (Angi), up to $1,500 (Forbes), $1,346 to $2,673 (Fixr). | $500 – $2,673 | Angi (HomeAdvisor) (opens in a new tab)Forbes Home (opens in a new tab)Fixr (opens in a new tab) | Source reviewed |
| Condensate line clearing costs $75 to $250 and a condensate pump $100 to $450 (Fixr, AC and heat pump repair pages). | $75 – $450 | Fixr (opens in a new tab) | Source reviewed |
| Fixr furnace repair page: $66 low end and $2,673 high end (the snapshot's outer ends); control board $390 to $725. | $66 – $2,673 | Fixr (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 4 independent (12 pages)
- 1.
- 2.Fixr: Furnace Repair Cost (opens in a new tab)Read Nov 9, 2026
- 3.
- 4.
- 5.
- 6.
- 7.Fixr: Furnace Replacement Cost 2026 (opens in a new tab)Read Nov 9, 2026
- 8.
- 9.
- 10.
- 11.Fixr: Water Heater Repair Cost (opens in a new tab)Read Nov 9, 2026
- 12.
Wage data and technical references
What changed
- Typical range now Fixr's published 2026 furnace repair range ($150 to $600, $350 to $400 average) instead of our $150 to $650 planning band; low and high ends now Fixr's $66 and $2,673. The unpublished $300 to $750 major-part row was replaced by Fixr's control board price. Added a furnace-vs-water-heater answer for "heater repair" estimates and answers on failure signs, warranty and timing.
