PlumbingFull System Replacement
Gas Water Heater Replacement Cost in 2026: Tank Sizes, Labor, Venting & Repairs
Gas water heater replacement typically costs $1,000 to $2,700. Fixr average: $1,900.
Cost snapshot
U.S. national figures ·
- Typical range
- $1,000 – $2,700
- Fixr average
- $1,900
- Full range
- $700 – $4,000
Where the typical range comes from: Fixr's published range for replacing a standard gas tank in an existing gas setup; the full range comes from Fixr's tank-size table ($700 for 30 to 40 gallons up to $4,000 for 80 gallons).
Replacing a gas water heater costs $1,000 to $2,700 for a standard tank in an existing gas setup, about $1,900 on average, according to Fixr. Angi lists gas models at $700 to $2,700 installed. Plumber labor is only $200 to $650 of that (Fixr); the rest is the heater, venting, disposal ($100 to $500) and a permit ($25 to $300). New venting adds about $500 for a direct vent and about $1,100 for a power vent. Size matters: Fixr lists $700 to $2,300 for a 40-gallon gas tank and $900 to $2,500 for 50 gallons.

Overview
Gas Water Heater Replacement Cost: Overview
Gas water heater replacement costs $1,000 to $2,700, about $1,900 on average. Compare tank sizes, plumber labor, venting, flue pipe, thermocouple and permits.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $1,000 – $2,700Fixr average: $1,900 | Medium confidence; cited: Fixr, Angi |
| Equipment or materials | $600 – $1,000 | Cited: This Old House, The Home Depot |
| Labor | $200 – $650 | Cited: Fixr |
By size
Cost by Size & Scope
Plumbing costs scale with tank capacity or flow rate, pipe run length, and how difficult the work area is to reach.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| 30-Gallon Gas Tank | 1–2 people (Fixr). Average shown is the calculated midpoint. | $700 – $2,100 | $1,400 | Fixr |
| 40-Gallon Gas Tank | 1–4 people (Fixr). Average shown is the calculated midpoint. | $700 – $2,300 | $1,500 | Fixr |
| 50-Gallon Gas Tank | 3–5 people (Fixr). Average shown is the calculated midpoint. | $900 – $2,500 | $1,700 | Fixr |
| 75-Gallon Gas Tank | 4–6 people (Fixr; 80 gallons: $1,300 – $4,000). Average shown is the calculated midpoint. | $1,100 – $3,500 | $2,300 | Fixr |
By type
Cost by Equipment & Installation Method
| Type | What it involves | Typical cost |
|---|---|---|
| Standard (Atmospheric Vent) Gas TankUses the existing vent | Exhaust rises through an existing metal flue or chimney. Fixr's typical range for a standard tank in an existing gas setup. | $1,000 – $2,700 installedFixr |
| Power-Vent Gas TankNeeds an outlet and a wall vent | A blower pushes exhaust out through a side wall, useful without a chimney. Fixr's gas water heater guide puts a new power vent at about $1,100; its installation guide lists power venting at $300 to $1,000, and This Old House at $300 to $600 plus $300 to $500 of electrical work. | Tank price + about $1,100 ventingFixr, This Old House |
| Direct-Vent Gas TankSealed combustion | Sealed combustion that draws air from outside. Fixr puts new direct venting at about $500; This Old House lists $500 to $1,000. | Tank price + $500 – $1,000 ventingFixr, This Old House |
| Higher-Efficiency Gas TankDOE cost analysis, 2022 dollars | The Department of Energy's 2024 rule estimates average installed costs in 2022 dollars from $1,432 for a baseline gas tank to $1,470 to $2,241 at the higher efficiency levels in its cost table. DOE does not label the $2,241 level a condensing model, and it says the rule does not require a condensing gas tank. | $1,470 – $2,241 installed (DOE) |
| Gas TanklessOn-demand | No storage tank; usually needs new venting and a larger gas line. See the tankless water heater installation cost guide. | $1,600 – $4,000 installedFixr |
Breakdown
Parts vs. Labor Breakdown
What the equipment or materials cost compared with the installer's labor, and what each figure is based on.
Licensed Plumbers & Gasfitters
- Labor range
- $200 – $650
- Planning estimate of on-site hours
- 2 – 3 hrs
- BLS median employee wage
- $30.67/hr
- Equipment or materials: $600 – $1,000
- The new gas tank. This Old House lists $600 to $1,000 for a tank unit and about $800 for a gas model before venting. Home Depot listed a Rheem 50-gallon natural gas tank (XG50T06EC38U1) at $719 on 2026-10-09, equipment only.
- Labor: $200 – $650
- Plumber labor for a gas tank swap: shutting off gas, draining and disconnecting the old tank, connecting water, gas and the vent, leak testing and lighting. Fixr lists $200 to $650 (about 20% to 25% of the total) and $45 to $200 per hour, and says a professional takes two to three hours on average to install a gas tank. Benchmark: BLS reports a May 2025 national median wage of $30.67 per hour for plumbers, pipefitters, and steamfitters; that is what an employee earns, not what a contractor bills.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| Venting Replacement | $500 – $1,100Fixr | As Needed | About $500 for a direct vent and about $1,100 for a power vent (Fixr). |
| Basic Gas Venting or Chimney Liner | $300 – $700This Old House | As Needed | Basic gas venting $300 to $500; a new chimney liner $500 to $700 (This Old House). |
| Thermal Expansion Tank | $40 – $150This Old House | As Needed | Where the city requires one (This Old House). |
| Permit with a New Gas Line | $1,500+Fixr | As Needed | Fixr's figure for permits and inspections when a new gas line or major plumbing changes are involved. |
| Switching from Electric to Gas | $1,500 – $2,300This Old House, Fixr | Optional | New gas lines when converting from electric (This Old House). Fixr reports $3,500 or more to switch from electric or oil to gas. |
Calculator
Gas Water Heater Replacement Cost Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Tank size
2Venting
A ZIP code scales the labor share of the estimate (about 35%) by the BLS wage ratio for the trade.
National planning estimate. Not a quote.
- Tank size: Not sure (standard tank)
- $1,000 – $2,700
- Venting
- Existing vent or flue
- Location
- National
A ZIP code or state changes only the labor share of the estimate, using the BLS Occupational Employment and Wage Statistics (May 2025) wage ratio for the trade. Materials, equipment and permits stay at national figures. Planning estimates, not contractor quotes.
The 'not sure' option is this guide's typical range from the cost snapshot.
Size options use Fixr's installed ranges by tank size from the table on this page.
Venting options add Fixr's published figures: about $500 for a direct vent and about $1,100 for a power vent.
Assumes an adequate gas supply. A new gas line, permit upgrades and fuel conversion are not included.
Location
Personalize This Estimate by ZIP or State
A ZIP code or state changes only the labor share of this guide's range (about 35%), using BLS wage data for the trade. Materials, equipment and permits stay at national figures. Results are estimates, not contractor quotes.
National figures: typical $1,000 – $2,700, average $1,900.
Leave empty for national figures.
$1,900
National average $1,900 · no location applied
- Typical range
- $1,000 – $2,700
- Full project range
- $700 – $4,000
- Labor index (BLS wage ratio)
- 1.00×
- Materials, equipment, permits
- National (not adjusted)
$200 – $650
National labor band. Hourly rate cited in this guide: $45–$200/hr (national).
$600 – $1,000
This guide's national allowance (see its sources); not adjusted by location.
Permits and inspections
This guide's permit allowance: $25 – $300. Fees and rules are set by each city or county; this is not a local fee lookup, so ask the contractor who pulls the permit and what it costs.
Typical range in all 50 states and DC
Modeled, not published by a source: the national typical range with the labor share (about 35%) scaled by each state's BLS Occupational Employment and Wage Statistics (May 2025) mean wage for plumbers, pipefitters, and steamfitters, divided by the national mean of $34.70/hr. Materials, equipment and permits stay national.
| State | BLS mean wage | Labor index | Typical range | Average | Action |
|---|---|---|---|---|---|
| Alabama | $27.77/hr | 0.80× | $930 – $2,500 | $1,775 | |
| Alaska | $43.49/hr | 1.25× | $1,100 – $2,950 | $2,075 | |
| Arizona | $32.66/hr | 0.94× | $980 – $2,650 | $1,850 | |
| Arkansas | $24.35/hr | 0.70× | $895 – $2,425 | $1,700 | |
| California | $39.58/hr | 1.14× | $1,050 – $2,825 | $2,000 | |
| Colorado | $33.22/hr | 0.96× | $985 – $2,650 | $1,875 | |
| Connecticut | $36.25/hr | 1.04× | $1,025 – $2,750 | $1,925 | |
| Delaware | $32.75/hr | 0.94× | $980 – $2,650 | $1,875 | |
| District of Columbia | $43.85/hr | 1.26× | $1,100 – $2,950 | $2,075 | |
| Florida | $26.94/hr | 0.78× | $920 – $2,500 | $1,750 | |
| Georgia | $27.99/hr | 0.81× | $935 – $2,525 | $1,775 | |
| Hawaii | $39.81/hr | 1.15× | $1,050 – $2,850 | $2,000 | |
| Idaho | $28.10/hr | 0.81× | $935 – $2,525 | $1,775 | |
| Illinois | $44.91/hr | 1.29× | $1,100 – $2,975 | $2,100 | |
| Indiana | $36.37/hr | 1.05× | $1,025 – $2,750 | $1,925 | |
| Iowa | $33.67/hr | 0.97× | $990 – $2,675 | $1,875 | |
| Kansas | $34.33/hr | 0.99× | $995 – $2,700 | $1,900 | |
| Kentucky | $33.11/hr | 0.95× | $985 – $2,650 | $1,875 | |
| Louisiana | $30.11/hr | 0.87× | $955 – $2,575 | $1,800 | |
| Maine | $32.00/hr | 0.92× | $975 – $2,625 | $1,850 | |
| Maryland | $35.34/hr | 1.02× | $1,000 – $2,725 | $1,900 | |
| Massachusetts | $43.46/hr | 1.25× | $1,100 – $2,950 | $2,075 | |
| Michigan | $37.14/hr | 1.07× | $1,025 – $2,775 | $1,950 | |
| Minnesota | $41.68/hr | 1.20× | $1,075 – $2,900 | $2,025 | |
| Mississippi | $27.25/hr | 0.79× | $925 – $2,500 | $1,750 | |
| Missouri | $36.06/hr | 1.04× | $1,025 – $2,725 | $1,925 | |
| Montana | $37.59/hr | 1.08× | $1,025 – $2,775 | $1,950 | |
| Nebraska | $31.59/hr | 0.91× | $970 – $2,625 | $1,850 | |
| Nevada | $34.38/hr | 0.99× | $995 – $2,700 | $1,900 | |
| New Hampshire | $31.84/hr | 0.92× | $970 – $2,625 | $1,850 | |
| New Jersey | $44.51/hr | 1.28× | $1,100 – $2,975 | $2,100 | |
| New Mexico | $29.71/hr | 0.86× | $950 – $2,575 | $1,800 | |
| New York | $40.29/hr | 1.16× | $1,050 – $2,850 | $2,000 | |
| North Carolina | $27.27/hr | 0.79× | $925 – $2,500 | $1,750 | |
| North Dakota | $31.81/hr | 0.92× | $970 – $2,625 | $1,850 | |
| Ohio | $33.51/hr | 0.97× | $990 – $2,675 | $1,875 | |
| Oklahoma | $28.35/hr | 0.82× | $935 – $2,525 | $1,775 | |
| Oregon | $47.33/hr | 1.36× | $1,125 – $3,050 | $2,150 | |
| Pennsylvania | $37.05/hr | 1.07× | $1,025 – $2,775 | $1,950 | |
| Rhode Island | $39.23/hr | 1.13× | $1,050 – $2,825 | $1,975 | |
| South Carolina | $26.87/hr | 0.77× | $920 – $2,475 | $1,750 | |
| South Dakota | $26.70/hr | 0.77× | $920 – $2,475 | $1,750 | |
| Tennessee | $29.09/hr | 0.84× | $945 – $2,550 | $1,800 | |
| Texas | $29.22/hr | 0.84× | $945 – $2,550 | $1,800 | |
| Utah | $30.87/hr | 0.89× | $960 – $2,600 | $1,825 | |
| Vermont | $33.16/hr | 0.96× | $985 – $2,650 | $1,875 | |
| Virginia | $29.16/hr | 0.84× | $945 – $2,550 | $1,800 | |
| Washington | $42.69/hr | 1.23× | $1,075 – $2,925 | $2,050 | |
| West Virginia | $28.26/hr | 0.81× | $935 – $2,525 | $1,775 | |
| Wisconsin | $40.73/hr | 1.17× | $1,050 – $2,875 | $2,025 | |
| Wyoming | $29.76/hr | 0.86× | $950 – $2,575 | $1,800 |
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Atmospheric Gas Water Heater: Gas Control, Burner, Flue and Draft Hood
Part 1: Gas control valve and thermostat
Senses the water temperature and opens the gas supply to the burner when the tank needs heat.
Part 2: Burner and pilot
Heat the tank from below.
Part 3: Flue, baffle and draft hood
Exhaust rises through the center of the tank past a baffle that slows it to transfer more heat, then leaves through the draft hood into the vent pipe.
Part 4: Temperature and pressure relief valve
Opens if the water gets too hot or the pressure too high; its discharge pipe runs down toward the floor or a drain.
Code and safety: Replacing a gas water heater usually needs a plumbing permit, and in some places a separate gas permit. Ask the installer to confirm the vent connection, the gas line and the relief-valve discharge.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Plumbing fixture fitting and trim manufacturing (PPI) (opens in a new tab) | 398.136 | 417.588 | +4.9% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Payback
Energy Savings & Replacement Payback
Compare the operating cost of an older, less efficient unit with a more efficient replacement, and how long the difference takes to pay back.
Modeling assumption: your household’s daily use.
Modeling assumption: supply to tank setting, e.g. 50°F to 120°F.
Uniform Energy Factor from the EnergyGuide label (example value).
From the model you are quoted (example value).
Starts at the tankless water heater guide average.
Enter the repair you were quoted, if any.
EIA 2025 U.S. residential average: 17.23¢ per kWh.
EIA 2025 U.S. residential price, about $1.48 per therm.
From your utility or tax filing.
About $11 a month.
- Payback on the extra cost
- 22 years
- 10-year net result
- −$1,529
- Replacement
- $2,800
- Net out of pocket
- $2,800
- Repair instead
- Not entered
- Extra cost to recover
- $2,800
- 10-year utility savings
- $1,271
- 10-year return on the extra cost
- −55%
- CO₂ avoided a year (approx.)
- 1,001 lb
Defaults you can change: electricity 17.23¢ per kWh (EIA, U.S. residential average for 2025) and natural gas about $1.48 per therm (EIA's 2025 residential $15.34 per thousand cubic feet at 1,037 Btu per cubic foot; our conversion).
Energy a year = gallons a day × 8.34 lb × temperature rise × 365 ÷ UEF, in kWh (÷ 3,412 Btu) or therms (÷ 100,000 Btu). Use, temperature rise and UEF ratings are modeling assumptions you can change.
CO₂ uses 0.767 lb per kWh (EPA eGRID, 2023 U.S. average) and 11.67 lb per therm (EIA). Savings are not guaranteed; your bills, rates and use decide the result.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $1,900
$1,000 – $2,700
Average $1,900
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Gas Water Heater Replacement Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
Fixr reports $1,000 to $2,700 for a standard gas tank in an existing gas setup, $1,900 on average. Angi lists gas models at $700 to $2,700. For comparison, the Department of Energy's 2024 rule estimated $1,432 installed for a baseline gas tank in 2022 dollars. New venting, a new gas line or a move to a new location adds to those figures.
Fixr puts labor for a gas tank replacement at $200 to $650, about 20% to 25% of the total, with plumbers billing $45 to $200 per hour. This Old House lists $300 to $800 for tank labor in general. Labor for a gas tankless unit is higher: $800 to $2,000 (Fixr). Our water heater installation labor cost guide covers labor-only quotes.
Fixr lists $900 to $2,500 installed for a 50-gallon gas tank and $700 to $2,300 for 40 gallons. Angi lists $800 to $2,500 for a 50-gallon water heater of any fuel. As a retail reference, Home Depot listed a Rheem 50-gallon natural gas tank at $719 on 2026-10-09, equipment only.
Fixr puts venting replacement at $500 to $1,100: about $500 for a direct vent and about $1,100 for a power vent. This Old House lists basic gas venting at $300 to $500 and a new chimney liner at $500 to $700. Fixr prices a backdraft repair, which may include new venting, at $100 to $500. None of these sources prices a short section of flue pipe on its own, so ask for a written quote that says what is replaced.
Fixr lists a thermocouple replacement at $150 to $325 including labor. Related gas repairs: pilot light $75 to $150 and gas control valve $150 to $300. Fixr's average water heater repair is $450, and it notes that a repair quote of $1,000 or more may favor replacing the heater instead.
An atmospheric (standard) vent lets hot exhaust rise through a metal flue or chimney. A power vent uses an electric blower to push exhaust through a side wall, so it needs an outlet. A direct vent draws combustion air from outside through a sealed pipe. Fixr puts new venting at about $500 for direct vent and about $1,100 for power vent; a standard tank that reuses a sound flue avoids that cost.
Fixr lists propane water heaters at $700 to $2,500 installed and natural gas at $700 to $2,700. Its gas water heater guide says propane units "cost about the same as natural gas water heaters, but they generally cost more to run." This Old House lists propane systems from $700 before the propane tank is installed.
This Old House lists $1,500 to $2,300 for new gas lines when converting from electric. Fixr reports $3,500 or more to switch from electric or oil to gas, and permits with a new gas line can reach $1,500 or more. See the gas line installation cost guide for per-foot pricing.
Repairs to the gas controls are usually far cheaper than a new heater: thermocouple $150 to $325, gas control valve $150 to $300 and anode rod $125 to $300, including labor (Fixr). A leaking tank body cannot be repaired. Fixr says repairs are usually worthwhile if the unit has at least half its lifespan remaining, and that tank models last 8 to 12 years; the Department of Energy assumes about 14.5 years for gas storage water heaters. Fixr also advises inspecting and replacing the anode rod every 2 to 3 years to slow tank corrosion.
Fixr lists not enough hot water, a unit at the end of its expected life (8 to 12 years for a tank), discolored water, unusual noises, leaks and unusually high energy bills. This Old House suggests considering a replacement at about 10 years old or when the heater produces rusty water.
Fixr says a professional takes two to three hours on average to install a gas tank, and four to six hours for a tankless unit. Fixr also says most municipalities require permits for plumbing and gas line work; a simple permit costs $25 to $300, and $1,500 or more when a new gas line or major plumbing changes are involved.
DOE's 2024 rule estimates average installed costs for gas-fired storage water heaters (20 to 55 gallons) in 2022 dollars: about $1,432 for a baseline model and $1,470 to $2,241 at the higher efficiency levels in its cost table. These are national averages from DOE's analysis, so current prices are higher after inflation. The rule's new standards apply to water heaters manufactured or imported from May 6, 2029; for gas storage tanks DOE adopted its efficiency level 2 and says the rule does not require a condensing level. It does not require replacing a heater that already works.
The tank model and size, labor, gas and water connections, a gas leak test, how the vent is reused or replaced, haul-away of the old unit ($100 to $500 per Fixr) and the permit ($25 to $300 for a simple permit). Red flags: no mention of the vent on a power-vent or direct-vent unit, no permit where your city requires one, or a quote that assumes the existing gas line is adequate without checking it.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Gas water heater replacement costs $1,000 to $2,700 for a standard tank in an existing gas setup, $1,900 on average (Fixr). | $1,000 – $2,700 | Fixr (opens in a new tab) | Source reviewed |
| Labor for a gas tank replacement costs $200 to $650, about 20% to 25% of the total (Fixr). | $200 – $650 | Fixr (opens in a new tab) | Source reviewed |
| Venting replacement costs about $500 for a direct vent and about $1,100 for a power vent (Fixr). | $500 – $1,100 | Fixr (opens in a new tab) | Source reviewed |
| A water heater thermocouple replacement costs $150 to $325 including labor (Fixr). | $150 – $325 | Fixr (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 3 independent (5 pages)
- 1.
- 2.
- 3.Fixr: Water Heater Repair Cost (opens in a new tab)Read Nov 9, 2026
- 4.
- 5.
Wage data and technical references
- 6.
- 7.
- 8.
What changed
- Corrected the Department of Energy figure: $2,241 is the highest efficiency level in DOE's cost table, not a "condensing" model, and DOE says its 2024 rule does not require a condensing gas tank; added the rule's May 2029 compliance date. Hours and hourly rate now use Fixr's published figures (2 to 3 hours, $45 to $200 per hour). Anode rod price now from Fixr instead of a 2022 Bob Vila page. Added replacement signs, lifespan and permit answers; size-table averages labeled as calculated midpoints.
