RoofingComponent Replacement
Roof Decking Replacement Cost in 2026: Price per Square Foot, per Sheet & Labor
Roof decking replacement typically costs $2 to $8 per sq ft installed. Midpoint of Fixr's range: $5 per sq ft installed.
Cost snapshot
U.S. national figures ·
- Typical range
- $2 – $8
- per sq ft installed
- Midpoint of Fixr's range
- $5
- Full range
- $2 – $8
Where the typical range comes from: Fixr's published installed price for replacing roof decking (roof replacement guide, February 2026); HomeGuide lists $2 to $5 per sq ft.
Roof decking replacement costs $2 to $8 per square foot installed (Fixr, 2026), which is about $64 to $256 per 4x8 sheet of 32 sq ft (calculated). HomeGuide lists $2 to $5 per sq ft, or $200 to $500 per 100 sq ft repaired. The $5 shown as the average is the midpoint of Fixr's range, not a published figure. Fixr's 2023 decking guide splits the job into $2.27 to $4.13 per sq ft for panels and $0.89 to $1.62 for labor, and its repair and shingle guides put decking repairs found during a re-roof at $150 to $1,000 in total. The panel itself is a small part of the price: a 7/16-in. OSB sheet was $14.51 at one Home Depot store in October 2026.

Overview
Roof Decking Replacement Cost: Overview
Roof decking replacement costs $2 to $8 per sq ft installed, about $64 to $256 per 4x8 sheet (Fixr). Compare labor, OSB vs plywood and full re-decking costs.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $2 – $8per sq ft installedMidpoint of Fixr's range: $5 per sq ft installed | Medium confidence; cited: Fixr, HomeGuide, The Home Depot |
| Equipment or materials | $2.27 – $4.13per sq ft installed | Cited: Fixr, The Home Depot |
| Labor | $0.89 – $1.62per sq ft installed | Cited: Fixr, This Old House, HomeGuide |
By size
Cost by Roof Size & Scope
Roofing costs scale with roof area (measured in squares of 100 sq ft), pitch, and how much of the roof the project covers.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| 2 Sheets (64 sq ft, calculated) | Spot repair around a vent or small leak; Fixr's $2 – $8 per sq ft, average = midpoint | $128 – $512 | $320 | Fixr |
| 4 Sheets (128 sq ft, calculated) | Rot along an eave or valley; Fixr's $2 – $8 per sq ft, average = midpoint | $256 – $1,024 | $640 | Fixr |
| 10 Sheets (320 sq ft, calculated) | Long-term leak or failed flashing section; Fixr's $2 – $8 per sq ft, average = midpoint | $640 – $2,560 | $1,600 | Fixr |
| 25 Sheets (800 sq ft, calculated) | One large roof plane; Fixr's $2 – $8 per sq ft, average = midpoint | $1,600 – $6,400 | $4,000 | Fixr |
| Full Re-Deck (2,000 sq ft, calculated) | Entire roof, e.g. replacing spaced plank decking; Fixr's $2 – $8 per sq ft, average = midpoint | $4,000 – $16,000 | $10,000 | Fixr |
By type
Cost by Material & Method
| Type | What it involves | Typical cost |
|---|---|---|
| OSB (Oriented Strand Board)Lower end of panel prices (Fixr) | Engineered wood strands bonded with resin; the most common residential roof sheathing. Panels only; OSB sits toward the low end (Fixr). A 7/16-in. 4x8 OSB sheet was $14.51 at one Home Depot store. | $2.27 – $4.13 / sq ft (Fixr)The Home Depot |
| Plywood (CDX or premium)Higher end of panel prices (Fixr) | Cross-laminated wood veneers; holds fasteners well and tolerates moisture. Panels only; premium plywood sits toward the high end (Fixr). Retail price not observed. | $2.27 – $4.13 / sq ft (Fixr) |
| Plank or Board DeckingOlder construction | Older homes may have solid or spaced boards; spaced boards are often sheathed over before new shingles. Fixr says plank decking "tends to be very expensive to install". | Not publishedFixr |
Breakdown
Parts vs. Labor Breakdown
What the equipment or materials cost compared with the installer's labor, and what each figure is based on.
Roofers (hours per 4x8 sheet)
- Labor range
- $0.89 – $1.62
- Planning estimate of on-site hours
- 0.4 – 0.7 hrs
- BLS median employee wage
- $26.65/hr
- Equipment or materials: $2.27 – $4.13
- Decking panels per sq ft as published by Fixr (2023): OSB toward the lower end, premium plywood toward the higher end. Retail panel prices are lower (7/16-in. OSB $14.51 per 4x8 sheet, about $0.45 per sq ft, at one Home Depot store in October 2026), so Fixr's figure likely includes the contractor's handling and markup.
- Labor: $0.89 – $1.62
- Decking labor per sq ft as published by Fixr (2023): $0.89 to $1.62, or about $28 to $52 per 4x8 sheet (calculated). Hours are per sheet and calculated ($28 to $52 divided by This Old House's $75 per hour for roofing labor); the $30 to $100 hourly range is HomeGuide's for roofers. Benchmark: BLS reports a May 2025 national median wage of $26.65 per hour for roofers (10th to 90th percentile: $18.01 to $39.29), an employee wage rather than a contractor rate.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| Decking Repair During a Re-Roof (total) | $150 – $1,000 (Fixr) | As Needed | Fixr's typical add-on when some rotted sheathing is found after tear-off. |
| Rafter or Framing Repair | Up to $5,000 added (Fixr) | As Needed | Significant rafter damage under long-term leaks. |
| Fascia and Soffit Repairs | $500 – $2,500 (Fixr) | As Needed | Rotted boards at the eaves, often found at the same time. |
| Sagging Roof Repair | $800 – $5,000 (Fixr) | As Needed | When the decking and possibly the rafters have lost strength. |
| Re-Roofing Permit | $100 – $500 (Fixr) | Required | Per project, not per sheet; decking work is usually covered by the re-roofing permit. |
Calculator
Roof Decking Replacement Cost Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Decking area to replace
This project is priced with national figures only; a ZIP code does not change it.
About $2 – $8 per sq ft for 320 sq ft
National planning estimate. Not a quote.
- Decking area to replace: 10 sheets, 320 sq ft (long-term leak area)
- $640 – $2,560
- Location
- National
This project uses national figures only: the sources do not publish a labor split for it, so no ZIP or state adjustment is applied. Planning estimates, not contractor quotes.
Area options multiply Fixr's $2 to $8 per sq ft for replacing roof decking by the area (one 4x8 sheet covers 32 sq ft); they match the calculated rows on this page.
Fixr places OSB toward the low end and plywood toward the high end of its panel prices; both fall inside the $2 to $8 installed range, so there is no separate panel option.
National planning range only; no regional adjustment is applied.
The re-roofing permit ($100 to $500, Fixr) is per project. Decking replaced as a stand-alone repair also includes removing and replacing the roofing above it.
Location
Personalize This Estimate by ZIP or State
This project is priced with national figures only: its sources publish it as a whole price without a labor split, so a ZIP code or state does not change it.
Roof Decking Replacement Cost in 2026: national figures only, $2 – $8 per sq ft installed.
Leave empty for national figures.
$5per sq ft installed
National average $5 · no regional adjustment for this project
- Typical range
- $2 – $8
- Full project range
- $2 – $8
- Labor index (BLS wage ratio)
- Not applied
- Materials, equipment, permits
- National (not adjusted)
$0.89 – $1.62
National labor band. Hourly rate cited in this guide: $30–$100/hr (national).
$2.27 – $4.13
This guide's national allowance (see its sources); not adjusted by location.
Permits and inspections
This guide does not price a permit. Rules are set by each city or county; ask the contractor whether one is needed and who pulls it.
No state table: this project uses national figures in every state.
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Replacing Roof Decking: OSB Sheets, Nailing Pattern and Panel Clips
Part 1: OSB or plywood sheets
4x8 panels nailed to the rafters or trusses. OSB usually costs less; plywood tolerates moisture better.
$2.27 – $4.13 / sq ft (Fixr) · The Home Depot
Part 2: Nailing pattern
Nails run along the panel edges and across the middle at the spacing the code and the panel maker specify.
Part 3: Panel clips (H-clips)
Support the panel edges between rafters and keep a small expansion gap between sheets.
Part 4: Underlayment
Goes over the new deck before the shingles.
Code and safety: Decking replacement is usually covered by the re-roof permit. Ask whether the quote prices decking per sheet or per square foot and how much is included before extra charges apply.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Asphalt shingle and coating materials manufacturing (PPI) (opens in a new tab) | 360.462 | 377.534 | +4.7% |
| Plywood (PPI) (opens in a new tab) | 271.138 | 300.124 | +10.7% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $5 per sq ft
$2 – $8per sq ft
Average $5
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Roof Decking Replacement Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
Fixr lists roof decking replacement at $2 to $8 per sq ft, which is about $64 to $256 per 4x8 sheet (calculated), and HomeGuide $2 to $5 per sq ft, or $200 to $500 per 100 sq ft repaired. When a roofer finds some rotted decking during a re-roof, Fixr puts the typical add-on at $150 to $1,000 in total. Replacing the decking on a whole 2,000 sq ft roof would be about $4,000 to $16,000 at Fixr's rates (calculated).
Fixr's decking guide (2023) lists labor at $0.89 to $1.62 per sq ft, about $28 to $52 per 4x8 sheet (calculated), on top of $2.27 to $4.13 per sq ft for the panels. For a 1,000 sq ft roof that example comes to $889 to $1,619 for labor and $3,160 to $5,749 in total.
Price them separately: the new roof itself (most roof replacements cost $7,500 to $14,000, according to Fixr; see our roof replacement guide) plus decking only where it is damaged, at $2 to $8 per sq ft (Fixr) or $2 to $5 (HomeGuide). Ask for a per-sheet or per-sq-ft decking price in the contract so the extra is not open-ended.
Fixr says OSB panels usually fall on the lower end of its $2.27 to $4.13 per sq ft range and premium plywood on the higher end. At retail, a 7/16-in. OSB sheet was $14.51 at one Home Depot store in October 2026. Both are common residential roof sheathing; follow your local code and the shingle manufacturer's requirements for thickness.
Fixr lists the warning signs as roof leaks, stains on walls or ceilings, mold, mildew or water damage on the rafters, a sagging roofline and rotten boards. Soft spots are usually confirmed once the old shingles are torn off.
Yes. Sheathing and decking both mean the plywood, OSB or boards nailed to the rafters under the underlayment and shingles. This guide covers wood decking on houses; corrugated steel deck used on commercial buildings is a different product priced by gauge and profile and is not covered here.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Fixr lists roof decking replacement at $2 to $8 per sq ft (about $64 to $256 per 4x8 sheet, calculated). | $2 – $8 per sq ft | Fixr (opens in a new tab) | Source reviewed |
| Fixr (2023) lists decking panels at $2.27 to $4.13 per sq ft and labor at $0.89 to $1.62 per sq ft. | $3.16 – $5.75 per sq ft combined (calculated) | Fixr (opens in a new tab) | Source reviewed |
| Fixr lists decking repairs found during a re-roof at $150 to $1,000. | $150 – $1,000 | Fixr (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 3 independent (8 pages)
- 1.
- 2.
- 3.
- 4.
- 5.
- 6.
- 7.
- 8.
Wage data and technical references
What changed
- The $5 average is now labelled as the midpoint of Fixr's range. HomeGuide's $2 to $5 per sq ft added as a second independent publisher (confidence raised from low to medium under the documented rule). Labor hours are now per 4x8 sheet and calculated from Fixr's published labor price.
