RoofingDemolition & Surface Prep
Roof Tear-Off Cost in 2026: Shingle Removal & Disposal Pricing
A roof tear-off typically costs $1,000 to $3,000 (for a ~2,000 sq ft roof). Fixr average × 20 squares (calculated): $1,000.
Cost snapshot
U.S. national figures ·
- Typical range
- $1,000 – $3,000
- for a ~2,000 sq ft roof
- Fixr average × 20 squares (calculated)
- $1,000
- Full range
- $600 – $5,250
Where the typical range comes from: Calculated from Fixr's $50 per square average and $150 per square upper figure for a 2,000 sq ft (20-square) roof; the full range applies the same prices to 12 to 35 squares.
Roof tear-off costs about $1,000 to $3,000 for a 2,000 sq ft roof when it is billed separately: Fixr reports $50 per roofing square on average including dumping fees, and up to $150 per square for heavy materials such as concrete tile or extra layers of asphalt. Fixr's average is also the low end, because the higher figure applies only to heavy or multi-layer roofs. Other publishers are higher: HomeGuide lists $1 to $3 per sq ft for shingles ($100 to $300 per square), and HomeAdvisor $1,500 to $4,500 for removal and disposal, or $1 to $5 per sq ft (Angi, its parent company, publishes the same per-sq-ft range). Most roofers include tear-off in a replacement quote, so confirm whether yours does.

Overview
Roof Tear-off Cost: Overview
Roof tear-off costs about $1,000 to $3,000 for a 2,000 sq ft roof at Fixr's $50 to $150 per square. See what layers and tile add, and when it is included.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $1,000 – $3,000for a ~2,000 sq ft roofFixr average × 20 squares (calculated): $1,000 for a ~2,000 sq ft roof | Low confidence; cited: Fixr, HomeGuide, HomeAdvisor |
| Whole-job price (no labor split published) | $1,000 – $3,000for a ~2,000 sq ft roof | Cited: Fixr, This Old House |
By size
Cost by Roof Size & Scope
Roofing costs scale with roof area (measured in squares of 100 sq ft), pitch, and how much of the roof the project covers.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| 1,200 sq ft roof (12 squares, calculated) | Small ranch or cottage; Fixr's $50 average to $150 per square | $600 – $1,800 | $600 | Fixr |
| 1,800 sq ft roof (18 squares, calculated) | Three-bedroom single story; Fixr's $50 average to $150 per square | $900 – $2,700 | $900 | Fixr |
| 2,000 sq ft roof (20 squares, calculated) | Basis of the typical range; Fixr's $50 average to $150 per square | $1,000 – $3,000 | $1,000 | Fixr |
| 2,200 sq ft roof (22 squares, calculated) | Four-bedroom home; Fixr's $50 average to $150 per square | $1,100 – $3,300 | $1,100 | Fixr |
| 2,800 sq ft roof (28 squares, calculated) | Large two-story home; Fixr's $50 average to $150 per square | $1,400 – $4,200 | $1,400 | Fixr |
| 3,500 sq ft roof (35 squares, calculated) | Very large home; Fixr's $50 average to $150 per square | $1,750 – $5,250 | $1,750 | Fixr |
By type
Cost by Material & Method
| Type | What it involves | Typical cost |
|---|---|---|
| Single-Layer Asphalt Shingle Tear-OffPer roofing square (Fixr) | Removing one layer of shingles, with dumping fees. About $0.50 per sq ft, including dumping fees. | $50 per square avg. (Fixr) |
| Multiple Layers or Heavy Tile RemovalPer roofing square (Fixr) | Extra layers or concrete or clay tile are heavier to remove and dump. | Up to $150 per squareFixr |
| Shingle or Metal vs Slate or Tile (HomeGuide)Per sq ft | Labor to remove the old material, by weight of the material. For shingles or metal ($100 to $300 per square); slate or tile $2 to $5 or more per sq ft. | $1 – $3 / sq ft (HomeGuide) |
| Removal and Disposal (HomeAdvisor)Per project or per sq ft | HomeAdvisor's roof replacement and shingle pages; Angi, its parent company, publishes the same per-sq-ft range and $1,000 – $5,000 in total. Per project; HomeAdvisor also lists $1 to $5 per sq ft. | $1,500 – $4,500 (HomeAdvisor) |
Breakdown
Parts vs. Labor Breakdown
The sources publish this job as one price, so there is no parts-versus-labor split to show; here is what that price covers.
Roofers
- Whole-job price
- $1,000 – $3,000
- BLS median employee wage
- $26.65/hr
- Equipment or materials
- Equipment and tarps are part of the service price; no separate figure is published.
- Whole-job price (no labor split published): $1,000 – $3,000
- Whole-service price: crew labor, the dumpster and dumping fees are bundled in Fixr's $50 per square average, with up to $150 for heavier materials or multiple layers. No publisher splits it, so the typical range is shown as the full price. Hours are calculated ($1,000 to $3,000 divided by This Old House's $75 per hour). Benchmark: BLS reports a May 2025 national median wage of $26.65 per hour for roofers, an employee wage rather than a contractor rate.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| Tear-Off Billed Separately | $50 – $150 / square (Fixr) | Common | Fixr's price when tear-off and disposal are not part of the replacement quote. |
| Demolition and Disposal of a Tile Roof | $1 – $5 per sq ftHomeAdvisor | As Needed | HomeAdvisor's tile roof page lists this for demolition and disposal of old roofing. |
| Roof Decking Found Rotted After Tear-Off | $2 – $8 per sq ft (Fixr)HomeGuide | As Needed | Only the damaged areas; ask for the unit price before work starts. HomeGuide lists $2 to $5. |
| Removal in a Hurricane-Zone State (example) | About $1 per sq ft (Fixr) | As Needed | Shows how removal prices vary by state and material; dated January 2025. Fixr's Florida page; up to $4 per sq ft for slate or metal. |
Calculator
Roof Tear-Off Cost Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Roof size
This project is priced with national figures only; a ZIP code does not change it.
National planning estimate. Not a quote.
- Roof size: Not sure (roof of about 2,000 sq ft)
- $1,000 – $3,000
- Location
- National
This project uses national figures only: the sources do not publish a labor split for it, so no ZIP or state adjustment is applied. Planning estimates, not contractor quotes.
The 'not sure' option is Fixr's $50 to $150 per roofing square for a roof of about 2,000 sq ft; size options use the calculated rows on this page (squares times $50 to $150).
Fixr's $150 per square top already covers heavy materials or more than one layer, so there is no separate heavy option.
National planning range only; no regional adjustment is applied.
Location
Personalize This Estimate by ZIP or State
This project is priced with national figures only: its sources publish it as a whole price without a labor split, so a ZIP code or state does not change it.
Roof Tear-Off Cost in 2026: national figures only, $1,000 – $3,000 (for a ~2,000 sq ft roof).
Leave empty for national figures.
$1,000for a ~2,000 sq ft roof
National average $1,000 · no regional adjustment for this project
- Typical range
- $1,000 – $3,000
- Full project range
- $600 – $5,250
- Labor index (BLS wage ratio)
- Not applied
- Materials, equipment, permits
- National (not adjusted)
The sources publish this job as one price, with no separate labor figure.
Equipment and supplies are included in the package price, so no separate allowance is shown.
Permits and inspections
This guide does not price a permit. Rules are set by each city or county; ask the contractor whether one is needed and who pulls it.
No state table: this project uses national figures in every state.
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Roof Tear-Off in Four Steps: Strip, Pull Underlayment, Expose, Sweep
Part 1: A. Strip the shingles
Shingles and nails are pried up with a roofing shovel and dropped onto tarps or straight into a dumpster.
Part 2: B. Pull the underlayment
The old felt or synthetic underlayment comes off too, so the deck can be inspected.
Part 3: C. Expose the decking
The bare deck is checked for rot and soft spots. Replacing damaged decking is usually priced separately.
$2 – $8 per sq ft (Fixr) · HomeGuide
Part 4: D. Sweep and haul away
The deck is swept, loose nails are collected from the yard and the debris leaves in a dumpster.
Code and safety: Many codes do not allow a new roof over two existing layers, which makes a full tear-off necessary; your local building department has the final say.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Asphalt shingle and coating materials manufacturing (PPI) (opens in a new tab) | 360.462 | 377.534 | +4.7% |
| Plywood (PPI) (opens in a new tab) | 271.138 | 300.124 | +10.7% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $1,000
$1,000 – $3,000
Average $1,000
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Roof Tear-off Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
Fixr reports $50 per roofing square on average including dumping fees (about $0.50 per sq ft), which is about $1,000 for a 2,000 sq ft roof, and up to $150 per square for heavier materials or multiple layers. Other publishers are higher: HomeGuide lists $1 to $3 per sq ft for shingles or metal and $2 to $5 or more for slate or tile, and HomeAdvisor $1,500 to $4,500 for removal and disposal. Angi, HomeAdvisor's parent company, lists $1 to $5 per sq ft or $1,000 to $5,000 in total.
Tear-off is usually part of a replacement quote: Fixr says most professionals include removing the old roof and hauling it away. A complete roof replacement typically costs $7,500 to $14,000 (Fixr; see our roof replacement guide). If tear-off is billed separately, add about $50 to $150 per square (Fixr), roughly $1,000 to $3,000 for 2,000 sq ft.
The sources describe different scopes. Fixr prices removal per roofing square including dumping fees, HomeGuide prices the labor per sq ft by material, and HomeAdvisor gives a per-project removal and disposal range without stating the roof size or number of layers. Angi and HomeAdvisor belong to the same company and count as one source, so this guide's range rests on one publisher (Fixr) and its confidence is low.
Yes. Fixr lists up to $150 per square for heavier materials such as concrete tile or multiple layers of asphalt shingles, compared with $50 per square on average; HomeGuide lists $2 to $5 or more per sq ft for slate or tile against $1 to $3 for shingles. HomeAdvisor's tile roof page lists demolition and disposal at $1 to $5 per sq ft.
Yes. Fixr's Florida page (January 2025) lists roof removal at about $1 per sq ft on average and up to $4 per sq ft for heavier materials such as slate or metal, which is above Fixr's national average of $50 per square ($0.50 per sq ft). Local dump fees and labor rates drive the difference, so ask for tear-off as a separate line in each quote.
Pick your roof area in squares and whether you are removing a single layer of shingles or heavy material and extra layers. The calculator starts from Fixr's $50 to $150 per square for a 20-square roof and scales it by roof size; the heavy-removal option is a planning assumption, and Fixr's published top is $150 per square. It is a national planning range with no ZIP adjustment.
Sometimes. Local codes decide: Fixr says some municipalities allow only one layer while others allow two or even three before a full tear-off is required, and HomeGuide says most cities limit roofs to two layers. HomeGuide adds that an overlay saves on removal but may shorten the roof's life, and HomeAdvisor that leaving the old roof in place hides rotting wood or leaks and adds load. Ask for both quotes to see the saving.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Fixr reports $50 per roofing square on average for tear-off including dumping fees, and up to $150 per square for heavier materials or multiple layers. | $50 – $150 per square | Fixr (opens in a new tab) | Source reviewed |
| HomeAdvisor lists $1,500 to $4,500 for removal and disposal and $1 to $5 per sq ft for removing old roofing; Angi (same company) lists $1 to $5 per sq ft or $1,000 to $5,000 in total. | $1 – $5 per sq ft | Angi (HomeAdvisor) (opens in a new tab) | Source reviewed |
| HomeGuide lists tear-off at $1 to $3 per sq ft for shingles or metal and $2 to $5 or more for slate or tile. | $1 – $5+ per sq ft | HomeGuide (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 4 independent (11 pages)
- 1.
- 2.
- 3.
- 4.
- 5.
- 6.
- 7.
- 8.
- 9.
- 10.
- 11.
Wage data and technical references
What changed
- The average is now labelled as Fixr's $50 per square times 20 squares, and the full range ($600 to $5,250) matches the size table. HomeGuide's and HomeAdvisor's higher removal prices added for comparison; HomeAdvisor no longer credited with Angi's $1,000 to $5,000 total. Overlay answer re-sourced; confidence set to low because one publisher supports the range.
