HVACFull System Replacement
Mini Split Installation Cost in 2026: Ductless Prices per Zone & BTU Size
Mini split installation typically costs $2,000 to $5,000. Angi's published average: $3,000.
Cost snapshot
U.S. national figures ·
- Typical range
- $2,000 – $5,000
- Angi's published average
- $3,000
- Full range
- $500 – $14,500
Where the typical range comes from: Angi's published typical range for a ductless mini split (Bob Vila republishes the same Angi/HomeAdvisor figures); the outer ends are the $500 low of the one-zone price and the $14,500 top that Fixr and Angi list for whole-home systems.
A ductless mini split typically costs $2,000 to $5,000 installed, about $3,000 on average, according to Angi; Bob Vila (page updated 2024) repeats Angi and HomeAdvisor's figures, so it is not a separate check. Price rises with each indoor unit (zone): This Old House lists averages of $2,750 for one zone, $4,550 for two, $5,450 for three and $6,650 for four. Independent figures run higher: Fixr's ductless page reports a $6,357 average ($4,577 to $8,328), and This Old House's survey owners paid $8,221 on average for a ductless replacement, so multi-zone quotes often land above the typical range. Fixr lists ductless systems at $1,000 to $14,500; the top of that range is for multi-zone, whole-home systems.

Overview
Mini Split Installation Cost: Overview
Mini split installation typically costs $2,000 to $5,000, about $3,000 on average (Angi). See ductless prices per zone and BTU, labor, wiring and refrigerants.
These figures come from the published cost sources listed under Methodology & sources; figures we calculate are labeled. Setting a ZIP code or state adjusts only the labor share, using Bureau of Labor Statistics wage data.
| What it covers | Typical range | Basis |
|---|---|---|
| Installed project | $2,000 – $5,000Angi's published average: $3,000 | Low confidence; cited: Angi, This Old House, Fixr, Bob Vila |
| Equipment or materials | $1,500 – $4,000 | Cited: This Old House |
| Labor | $300 – $1,500 | Cited: Bob Vila, Fixr, This Old House |
By size
Cost by Capacity & Scope
HVAC costs scale with system capacity (tonnage or motor size), the size of the home being served, and the scope of the work.
| Size or scope | Typical home coverage | Installed cost | Average | Source |
|---|---|---|---|---|
| 1 Zone (one indoor head) | This Old House range and published average | $500 – $5,000 | $2,750 | This Old House, Angi |
| 2 Zones | This Old House range and published average | $1,400 – $7,700 | $4,550 | This Old House, Angi |
| 3 Zones | This Old House range and published average | $1,800 – $9,100 | $5,450 | This Old House |
| 4 Zones | This Old House range and published average | $2,600 – $10,700 | $6,650 | This Old House, Angi |
By type
Cost by Equipment Type & Efficiency
| Type | What it involves | Typical cost |
|---|---|---|
| Wall-Mounted HeadLeast expensive (Fixr) | The most common indoor unit, mounted high on a wall. | Not published separatelyFixr |
| Ceiling CassetteMost expensive (Fixr) | Recessed into the ceiling with four-way airflow. | Not published separatelyFixr |
| Concealed-Duct or Floor ConsoleVaries by model | Hidden short-duct units or low-wall consoles. | Not published separatelyFixr |
| By Size: 12,000 BTU (1 ton)Installed (This Old House) | Single-room capacity in This Old House's size table (not labeled ductless-only). | $3,500 – $5,000This Old House |
| By Size: 24,000 BTU (2 tons)Installed (This Old House) | Larger single zone or a small multi-zone system. | $6,000 – $8,000This Old House |
| By Size: 36,000 BTU (3 tons)Installed (This Old House) | Multi-zone capacity. | $8,000 – $11,000This Old House |
| Mini Split RepairRepair (Fixr / This Old House) | Typical repair instead of replacement. | $300 – $1,000 (Fixr) · $250 – $900 (TOH)This Old House |
Breakdown
Parts vs. Labor Breakdown
What the equipment or materials cost compared with the installer's labor, and what each figure is based on.
HVAC Mechanics and Installers
- Labor range
- $300 – $1,500
- Planning estimate of on-site hours
- 6 – 16 hrs
- BLS median employee wage
- $29.33/hr
- Equipment or materials: $1,500 – $4,000
- Outdoor unit, indoor head(s), remote and line set. This Old House lists ductless mini-split AC equipment at $1,500 to $4,000 (heat pump models $1,300 to $8,000), excluding installation.
- Labor: $300 – $1,500
- Mounting the heads, drilling the wall, running lines and wiring, pressure test, vacuum and start-up. Bob Vila (2024) puts hiring an HVAC technician at $300 to $1,500; Fixr lists installers at $86 to $157 per hour, and This Old House reports 72% of owners paid $150 or more per hour. The 6 to 16 hours are a planning assumption. Benchmark: BLS reports a May 2025 national median wage of $29.33 per hour for HVAC mechanics and installers.
BLS reports what employees earn, not what contractors bill; contractor rates also cover insurance, vehicles, overhead and profit. We use the BLS wage only to adjust the labor share for your location.
Extras
Additional Line Items Often Needed
| Item | Typical added cost | Needed? | Notes |
|---|---|---|---|
| Electrician for a New Circuit | $101 – $183 per hourFixr | As Needed | Fixr. Most mini splits need a dedicated circuit and an outdoor disconnect; the total depends on the panel and the distance. |
| Condensate Pump | $100 – $450Fixr | As Needed | Fixr heat pump repair guide. Needed when a head cannot drain by gravity through an outside wall. |
| Permits | $250 – $400Angi, Fixr | Required | Angi. Fixr says the contractor typically secures the permits and includes the cost in the price. |
| Line Set Cover | Not published separatelyAngi | Optional | Decorative cover for the refrigerant lines on the outside wall. |
Calculator
Ductless Mini-Split Installation Estimator
Choose the options closest to your project for a planning range. It is not a quote; compare it with written, itemized proposals.
1Number of zones
A ZIP code scales the labor share of the estimate (about 35%) by the BLS wage ratio for the trade.
National planning estimate. Not a quote.
- Number of zones: Not sure (typical installation)
- $2,000 – $5,000
- Location
- National
A ZIP code or state changes only the labor share of the estimate, using the BLS Occupational Employment and Wage Statistics (May 2025) wage ratio for the trade. Materials, equipment and permits stay at national figures. Planning estimates, not contractor quotes.
The 'not sure' option is this guide's typical range from the cost snapshot.
Zone options use the rows of this page's zone table.
Fixr says ceiling cassettes cost more than wall-mounted heads but publishes no price, so the calculator does not price them.
Electrical work (an electrician bills $101 to $183 per hour, Fixr) and permits ($250 to $400, Angi) are not included.
Location
Personalize This Estimate by ZIP or State
A ZIP code or state changes only the labor share of this guide's range (about 35%), using BLS wage data for the trade. Materials, equipment and permits stay at national figures. Results are estimates, not contractor quotes.
National figures: typical $2,000 – $5,000, average $3,000.
Leave empty for national figures.
$3,000
National average $3,000 · no location applied
- Typical range
- $2,000 – $5,000
- Full project range
- $500 – $14,500
- Labor index (BLS wage ratio)
- 1.00×
- Materials, equipment, permits
- National (not adjusted)
$300 – $1,500
National labor band. Hourly rate cited in this guide: $86–$157/hr (national).
$1,500 – $4,000
This guide's national allowance (see its sources); not adjusted by location.
Permits and inspections
This guide's permit allowance: $250 – $400. Fees and rules are set by each city or county; this is not a local fee lookup, so ask the contractor who pulls the permit and what it costs.
Typical range in all 50 states and DC
Modeled, not published by a source: the national typical range with the labor share (about 35%) scaled by each state's BLS Occupational Employment and Wage Statistics (May 2025) mean wage for heating, air conditioning, and refrigeration mechanics and installers, divided by the national mean of $31.14/hr. Materials, equipment and permits stay national.
| State | BLS mean wage | Labor index | Typical range | Average | Action |
|---|---|---|---|---|---|
| Alabama | $24.67/hr | 0.79× | $1,850 – $4,625 | $2,775 | |
| Alaska | $38.53/hr | 1.24× | $2,175 – $5,425 | $3,250 | |
| Arizona | $29.28/hr | 0.94× | $1,950 – $4,900 | $2,925 | |
| Arkansas | $24.59/hr | 0.79× | $1,850 – $4,625 | $2,775 | |
| California | $36.24/hr | 1.16× | $2,125 – $5,275 | $3,175 | |
| Colorado | $34.29/hr | 1.10× | $2,075 – $5,175 | $3,100 | |
| Connecticut | $35.38/hr | 1.14× | $2,100 – $5,250 | $3,150 | |
| Delaware | $31.80/hr | 1.02× | $2,025 – $5,025 | $3,025 | |
| District of Columbia | $40.83/hr | 1.31× | $2,225 – $5,550 | $3,325 | |
| Florida | $27.55/hr | 0.89× | $1,925 – $4,800 | $2,875 | |
| Georgia | $27.44/hr | 0.88× | $1,925 – $4,800 | $2,875 | |
| Hawaii | $32.24/hr | 1.03× | $2,025 – $5,050 | $3,025 | |
| Idaho | $28.85/hr | 0.93× | $1,950 – $4,875 | $2,925 | |
| Illinois | $37.29/hr | 1.20× | $2,150 – $5,350 | $3,200 | |
| Indiana | $31.30/hr | 1.00× | $2,000 – $5,000 | $3,000 | |
| Iowa | $30.35/hr | 0.97× | $1,975 – $4,950 | $2,975 | |
| Kansas | $29.55/hr | 0.95× | $1,975 – $4,900 | $2,950 | |
| Kentucky | $28.30/hr | 0.91× | $1,925 – $4,850 | $2,900 | |
| Louisiana | $27.35/hr | 0.88× | $1,925 – $4,775 | $2,875 | |
| Maine | $31.39/hr | 1.01× | $2,000 – $5,025 | $3,000 | |
| Maryland | $35.49/hr | 1.14× | $2,100 – $5,250 | $3,150 | |
| Massachusetts | $37.38/hr | 1.20× | $2,150 – $5,350 | $3,200 | |
| Michigan | $31.01/hr | 1.00× | $2,000 – $5,000 | $3,000 | |
| Minnesota | $35.57/hr | 1.14× | $2,100 – $5,250 | $3,150 | |
| Mississippi | $25.49/hr | 0.82× | $1,875 – $4,675 | $2,800 | |
| Missouri | $30.01/hr | 0.96× | $1,975 – $4,925 | $2,950 | |
| Montana | $29.94/hr | 0.96× | $1,975 – $4,925 | $2,950 | |
| Nebraska | $29.35/hr | 0.94× | $1,950 – $4,900 | $2,950 | |
| Nevada | $30.46/hr | 0.98× | $1,975 – $4,950 | $2,975 | |
| New Hampshire | $34.37/hr | 1.10× | $2,075 – $5,175 | $3,100 | |
| New Jersey | $37.30/hr | 1.20× | $2,150 – $5,350 | $3,200 | |
| New Mexico | $26.60/hr | 0.85× | $1,900 – $4,750 | $2,850 | |
| New York | $35.94/hr | 1.15× | $2,100 – $5,275 | $3,150 | |
| North Carolina | $27.60/hr | 0.89× | $1,925 – $4,800 | $2,875 | |
| North Dakota | $33.66/hr | 1.08× | $2,050 – $5,150 | $3,075 | |
| Ohio | $31.73/hr | 1.02× | $2,025 – $5,025 | $3,025 | |
| Oklahoma | $27.71/hr | 0.89× | $1,925 – $4,800 | $2,875 | |
| Oregon | $32.90/hr | 1.06× | $2,050 – $5,100 | $3,050 | |
| Pennsylvania | $31.19/hr | 1.00× | $2,000 – $5,000 | $3,000 | |
| Rhode Island | $33.55/hr | 1.08× | $2,050 – $5,125 | $3,075 | |
| South Carolina | $27.14/hr | 0.87× | $1,900 – $4,775 | $2,875 | |
| South Dakota | $29.37/hr | 0.94× | $1,950 – $4,900 | $2,950 | |
| Tennessee | $27.79/hr | 0.89× | $1,925 – $4,800 | $2,875 | |
| Texas | $28.43/hr | 0.91× | $1,950 – $4,850 | $2,900 | |
| Utah | $28.85/hr | 0.93× | $1,950 – $4,875 | $2,925 | |
| Vermont | $32.24/hr | 1.03× | $2,025 – $5,050 | $3,025 | |
| Virginia | $29.42/hr | 0.94× | $1,950 – $4,900 | $2,950 | |
| Washington | $37.91/hr | 1.22× | $2,150 – $5,375 | $3,225 | |
| West Virginia | $24.85/hr | 0.80× | $1,850 – $4,650 | $2,800 | |
| Wisconsin | $32.41/hr | 1.04× | $2,025 – $5,075 | $3,050 | |
| Wyoming | $26.81/hr | 0.86× | $1,900 – $4,750 | $2,850 |
Regional figures use only U.S. Bureau of Labor Statistics Occupational Employment and Wage Statistics (May 2025) for the trade: the mean wage in the state, or in one of eight large cities for ZIP codes inside them, divided by the national mean. ZIP codes outside the 50 states and DC use national figures.
Anatomy
Ductless Mini-Split: Indoor Head, Line Set and Outdoor Inverter Unit
Part 1: Indoor wall unit (head)
Holds the indoor coil and fan. Each room or zone gets its own head.
Part 2: Line set, drain and control wire
Run together through one small hole in the wall: insulated copper refrigerant lines, a condensate drain tube and the wire that links the two units.
Part 3: Outdoor inverter unit
Holds the variable-speed compressor, coil and fan. One outdoor unit serves one head, or several on multi-zone models.
Part 4: Service valves and electrical connection
Where the installer connects, pressure-tests and evacuates the refrigerant lines, and where the dedicated circuit is wired in.
$101 – $183 per hour · Fixr
Code and safety: Mini-split installation usually needs a mechanical and an electrical permit, and charging or opening the refrigerant lines requires an EPA Section 608 certified technician.
Market
Input Price Changes: Last 12 Months
Contractor quotes move with the cost of materials, equipment, and labor. The chart shows how official U.S. Bureau of Labor Statistics (BLS) price and wage series changed between Aug 25 and Aug 26. These are national input indices, not the price of this project, and they are not a forecast.
| BLS series | Aug 25 | Aug 26 | 12-month change |
|---|---|---|---|
| Air-conditioning, refrigeration, and forced air heating equipment manufacturing (PPI) (opens in a new tab) | 312.596 | 324.82 | +3.9% |
| Average hourly earnings, specialty trade contractors (production and nonsupervisory) (opens in a new tab) | 37.02 | 38.94 | +5.2% |
Source: U.S. Bureau of Labor Statistics, Producer Price Index and Current Employment Statistics, retrieved 2026-10-08. Recent months are preliminary and can be revised for up to four months. Price indices are not seasonally adjusted. Each line is the percentage change from Aug 25.
Payback
Energy Savings & Replacement Payback
Compare the operating cost of an older, less efficient unit with a more efficient replacement, and how long the difference takes to pay back.
Modeling assumption: set it for your climate.
Enter both ratings in the same system (labels since 2023 show SEER2; an older label may show only SEER). The model divides cooling load by each rating.
Modeling assumption.
From the unit label (example value).
From the quote (example value).
Starts at the mini split guide average.
Starts at the AC compressor guide average.
EIA 2025 U.S. residential average: 17.23¢ per kWh.
EIA 2025 U.S. residential price, about $1.48 per therm.
From your utility or tax filing.
About $57 a month.
- Payback on the extra cost
- 2.1 years
- 10-year net result
- +$5,344
- Replacement
- $3,000
- Net out of pocket
- $3,000
- Repair instead
- $1,550
- Extra cost to recover
- $1,450
- 10-year utility savings
- $6,794
- 10-year return on the extra cost
- +369%
- CO₂ avoided a year (approx.)
- 3,025 lb
Defaults you can change: electricity 17.23¢ per kWh (EIA, U.S. residential average for 2025) and natural gas about $1.48 per therm (EIA's 2025 residential $15.34 per thousand cubic feet at 1,037 Btu per cubic foot; our conversion).
Cooling kWh = tons × 12,000 Btu × cooling hours ÷ (rating × 1,000); heat pump heating uses the same formula with heating hours and HSPF2. Hours and ratings are modeling assumptions you can change.
CO₂ uses 0.767 lb per kWh (EPA eGRID, 2023 U.S. average) and 11.67 lb per therm (EIA). Savings are not guaranteed; your bills, rates and use decide the result.
Quote check
Is Your Quote in the Typical Range?
Enter a written estimate to see where it falls against this guide's planning range for your labor market.
Within the typical range
Your quote: $3,000
$2,000 – $5,000
Average $3,000
Within the typical range. Quotes inside this range still differ with equipment, scope, access and warranty; compare itemized quotes line by line.
Getting comparable quotes
- Ask each contractor to price materials, labor, permits, disposal and optional work separately.
- Confirm the scope, equipment model, warranty, schedule and exclusions in writing.
- Compare like-for-like proposals from licensed, insured local contractors. Repair Cost Atlas does not match homeowners with contractors.
Direct answers
Frequently Asked Questions: Mini Split Installation Cost
Short, plain answers to the questions homeowners ask before contacting a contractor.
Angi puts most ductless mini split installations at $2,000 to $5,000, about $3,000 on average; Bob Vila (updated in 2024) cites the same Angi and HomeAdvisor data. This Old House lists about $3,250 for a single-zone unit in its heat pump guide. Independent figures for larger systems run higher: Fixr's ductless page reports a $6,357 average ($4,577 to $8,328), and This Old House's survey owners paid $8,221 on average for a ductless replacement. Fixr lists ductless systems up to $14,500 for whole-home multi-zone installs.
This Old House lists average installed prices of $2,750 for one zone ($500 to $5,000), $4,550 for two ($1,400 to $7,700), $5,450 for three ($1,800 to $9,100), $6,650 for four ($2,600 to $10,700) and $8,200 for five ($4,400 to $12,000). Angi publishes the same ranges for one, two and four zones, so the two may share data. Bob Vila (2024), which draws on Angi and HomeAdvisor, lists $2,000 to $8,800 for a single zone and $3,400 to $13,400 for three zones.
This Old House lists $3,500 to $5,000 for 12,000 BTU (1 ton), $6,000 to $8,000 for 24,000 BTU (2 tons) and $8,000 to $11,000 for 36,000 BTU (3 tons); it does not list 18,000 BTU separately, so expect a price between the 1-ton and 2-ton rows. Its size table is for split systems in general and is higher than its zone table.
Bob Vila (2024) puts hiring an HVAC technician at $300 to $1,500. Fixr lists installers at $86 to $157 per hour and an electrician at $101 to $183 per hour if a new circuit is needed; This Old House reports 72% of owners paid $150 or more per hour. Equipment alone runs $1,500 to $4,000 (This Old House).
For one or two rooms, usually yes: $2,000 to $5,000 against $5,000 to $12,000 for central AC (Fixr). For a whole house, a multi-zone mini split ($6,650 on average for four zones per This Old House) can approach central air, but it avoids ductwork ($3,600 to $9,500 per Fixr) in homes without ducts.
Fixr lists mini split repairs at $300 to $1,000 and This Old House at $250 to $900. This Old House suggests replacement when repair cost times the unit's age exceeds $5,000; Fixr applies the same rule to heat pumps and says heat pumps last 10 to 15 years.
They are related: VRF (variable refrigerant flow) systems also run several indoor units from one outdoor unit, but they are mainly commercial or large-home systems. The publishers we use (Angi and its sister site HomeAdvisor, Fixr and This Old House) do not publish residential VRF replacement prices, so we do not quote a range; ask for an itemized quote that lists capacity in tons and each indoor unit.
Yes, a multi-zone heat pump mini split can heat and cool several rooms from one outdoor unit. For cold climates, choose a model with ENERGY STAR's cold-climate designation and ask for its heating capacity at 5°F and its HSPF2 rating. Bob Vila (2024, drawing on Angi and HomeAdvisor) lists multiroom systems at $2,700 to $18,000.
New mini splits now use R-32 or R-454B. EPA's Technology Transitions rule lists mini-splits among the residential and light commercial systems limited to refrigerants with a global warming potential of 700 or less from January 1, 2025. ACHR News reports that Daikin moved its products to R-32, Johnson Controls uses R-32 for ductless models, and both refrigerants are classed as mildly flammable (A2L). An existing R-410A mini split can still be serviced and repaired (EPA). Fixr lists R-454B at $60 to $100 per pound and R-410A at $50 to $80 for later service.
Often. This Old House notes that some installations need panel upgrades, new circuits or local permits to meet code, and Angi lists permits at $250 to $400. Fixr says the HVAC contractor typically secures any necessary permits and includes the cost in the price, so ask whether the permit is in the quote.
This Old House says scheduling installation in spring or fall can lead to better pricing, because demand for cooling and heating work is lower than in summer and winter.
Included: the outdoor unit, indoor head(s), line set, wall penetration, mounting, vacuum and start-up. Often extra: a new electrical circuit and disconnect, a condensate pump ($100 to $450), line set covers and permits ($250 to $400 per Angi; Fixr says the contractor usually pulls them). Fixr recommends comparing equipment warranties and asking whether the installer also warrants the installation.
Be cautious when the quote does not list the capacity (BTU) of each head and the outdoor unit, leaves out the electrical work, or sizes every room the same without a load calculation. Fixr recommends comparing several estimates and asking whether the installer warrants the labor, not only the equipment.
Evidence
What supports these figures?
Each figure on this page and the published sources it is credited to. “Use with caution” marks figures we could not match to a published price. Wage, equipment and code references support only that narrower point, not an installed price.
| Estimate | Range or value | Published sources | Status |
|---|---|---|---|
| Angi: mini split installation averages $3,000, with a typical range of $2,000 to $5,000; Bob Vila (2024) repeats the same Angi/HomeAdvisor figures. | $2,000 – $5,000 | Angi (HomeAdvisor) (opens in a new tab)Bob Vila (opens in a new tab) | Source reviewed |
| This Old House: one zone averages $2,750 ($500 to $5,000); four zones $6,650 ($2,600 to $10,700). | $2,750 – $6,650 by zones | This Old House (opens in a new tab) | Source reviewed |
| Fixr lists ductless mini splits at $1,000 to $14,500 on its AC installation page; Bob Vila (2024) lists $2,000 to $14,500, credited to Angi and HomeAdvisor. | Up to $14,500 | Fixr (opens in a new tab)Bob Vila (opens in a new tab) | Source reviewed |
Sources
Methodology & Data Sources
The typical range and average come from the cost publishers listed below; we compare what they publish and label figures we calculate ourselves. Bureau of Labor Statistics (BLS) wage data adjusts only the labor share when you set a ZIP code or state. Technical references support specifications, not prices.
Cost publishers · 4 independent (13 pages)
- 1.
- 2.
- 3.
- 4.
- 5.
- 6.
- 7.
- 8.
- 9.
- 10.
- 11.
- 12.Fixr: Cost to Install Central Air (opens in a new tab)Read Nov 9, 2026
- 13.
Wage data and technical references
- 14.
- 15.
- 16.
- 17.
- 18.
What changed
- The summary now shows the higher independent figures (Fixr's $6,357 average and This Old House's $8,221 ductless replacement) next to Angi's $2,000 to $5,000. Bob Vila's figures come from Angi and HomeAdvisor, so they are no longer presented as a second source, and confidence is now low (one publisher behind the typical range). Low end lowered to the published $500 one-zone price, labor uses published figures, and new answers cover refrigerants (R-32, R-454B), permits and timing.
